background image

Important Notice

Evoqua Water Technologies Instruction Manuals are the safety documents for their products. The information provided therein 

is in accordance with the best practices known at the time of issue and, if fully implemented, should enable the user to operate 

the plant in the safest possible manner. It is therefore most important that instructions be read and understood prior to the 

installation, operation or maintenance of the plant.

Notes

Where necessary, special instructions are provided and are 

quoted under the following headings:

 WARNING:

 A warning is given in instances where 

failure to observe the instruction could result in injury to 

personnel.

 CAUTION:

 Cautions are given where failure to 

observe the instruction may result in equipment damage, 

or pollution to an allied system.

NOTE: Notes are provided to give additional emphasis to 

particular points of detail.

The following recommendations are made to ensure safe 

and efficient operation:-

1  Only suitably qualified personnel should install, operate 

and maintain the equipment.

2  Only Evoqua Water Technologies manufactured or 

approved parts should be used.

3  The equipment should not be used for any purpose other 

than that for which it was supplied. 

4  If equipment being supplied is being put into storage or 

not being commissioned immediately, or if the plant is being 

de-commissioned, Evoqua Water Technologies urge that 

they be contacted for detailed advice.

In an effort to make progressive improvements to products, 

changes in design may be incorporated from time to time, which 

may not be reflected immediately in the instruction manual. 

If in doubt, contact Evoqua Water Technologies quoting the 

equipment serial number; serial numbers are essential for 

effective communication and proper equipment identification.

The equipment described in this manual may be used with 

substances that themselves may be hazardous to personnel 

safety. It is essential that persons employed in the vacinity of 

such substances be aware of the appropriate safety practices 

and the location of suitable safety equipment. Provision of 

safety cards and codes of practice concerning hazardous 

substance should be made by the supplier of the substance.

Warranty

The equipment supplied is guaranteed against mechanical 

defect notified to the Seller within a period of 1 year from 

the date of delivery. For such guarantee to be valid the 

purchaser must notify the seller in writing immediately 

such defect becomes apparent. If the Seller so requires, 

the Purchaser shall return the defective equipment (at the 

Purchaser’s expense) to the Seller. The Seller undertakes 

that it will, at its own option and its own expense, and by way 

of full discharge of its guarantee obligation hereunder, either 

repair, or supply a replacement for the defective equipment, 

or refund any purchase monies paid to it in respect of any 

such defective equipment, or portion thereof. If title to the 

defective equipment is at the time of such replacement or 

refund vested in the Purchaser, then title shall thereupon 

vest in the Seller. Replacement material situated outside 

the U.K. will be supplied F.O.B. U.K. Port. The guarantee 

given in this clause shall not be operative and enforceable 

if the equipment is not operated strictly in accordance 

with the sellers instruction, or in the respect of any defect 

arising from accident, deliberate act, misuse, neglect or 

from a breach from the terms of the following clause, or 

in respect of any defect arising through damage incurred 

while being transported after delivery of the equipment, or if 

the equipment has been altered or modified in any way by 

any person other than the seller, or in respect of any other 

cause whatsoever which lies beyond the Sellers control.

The Purchaser must comply with all user instructions 

and safety recommendations issued by the Seller, and 

must install, commission and maintain the equipment in 

accordance with good engineering practice, and under the 

supervision of suitably qualified personnel, and the Seller 

shall not be liable to the Purchaser for any loss suffered 

as a result of the Purchaser’s breach of the terms of this 

clause.

Subject to this guarantee all conditions, warranties and 

representations, whether expressed or implied (by statute 

or otherwise) relating to the equipment, are hereby excluded 

in so far as they can be excluded without such exclusion 

being void or unenforceable at law.

Wallace & Tiernan, Barrier, Chem-Ad, DEPOLOX, OSEC, and V10k are trademarks of Evoqua, its subsidiaries or affiliates. 

The designations used in this publication may be trademarks whose use by third parties for their own purposes could 

violate the rights of the owners.All rights, especially those to duplication and distribution as well as translation, are 

reserved. No part of this document may be reproduced in any form (printing, photocopying, microfilm or any other 

method) or saved, processed, duplicated or distributed by the use of electronic systems without the express written 

consent of Evoqua Water Technologies.

Содержание WALLACE & TIERNAN DEOX/2000























































































Отзывы: