Evoqua WALLACE & TIERNAN DEOX/2000 Скачать руководство пользователя

Страница: 24 / 86

W3T331759 / WT.050.585.003.UE.IM.1014

MICRO/2000® AND DEOX/2000® MODULE

WARNING:

The device is not equipped with a mains switch and is in

operation as soon as the supply voltage is applied. When connecting

system components (e.g. devices, motors, pumps), the system components

must be switched off.

CAUTION:

To ensure safe and correct commissioning, knowledge of the

operation, connected electrical load, measurement signals, cable assignment

and fuse protection of the connected devices and machines and the relevant

safety regulations is required. The device may only be commissioned by

qualified and authorized electricians. Incorrectly connected devices can

be damaged, possibly irreparably, or cause faults in other equipment when

they are switched on or in operation. Ensure that the measuring and control

cables are not confused or make contact with one another. Never connect

or disconnect any cables to which voltage is applied.

NOTE:

Refer to manual W3T168777 for SFC fusing details and manual

W3T159207 for the MFC fusing details.

2.3.7 Mounting the housing covers

Carefully place the housing cover onto the flow block assembly

and drop into place.

2.4

System Shut Down

CAUTION:

Danger of uncontrolled dosing of chlorine or pH correction

medium: Shut down dosing system, close positioner!

NOTE:

If the installation site of the flow block assembly is not frost

free, the system must be shut down prior to any possible frost formation.

Switch off the power supply.

Drain the sample water supply line and drainage line (hold container

underneath).

Empty cell bodies and remove grit.

Dismantle the filter housing and/or check valve housing.

When the remaining water has drained from the flow control valve,

refit the filter housing and the check valve housing.

Remove the sensors from the cell body cover and disconnect from

the cable.

Содержание WALLACE & TIERNAN DEOX/2000























































































Результаты поиска

Содержание WALLACE & TIERNAN DEOX/2000

Отзывы:

Похожие инструкции для WALLACE & TIERNAN DEOX/2000

Бренды по названию

Популярные бренды

Evoqua WALLACE & TIERNAN DEOX/2000, Инструкция по эксплуатации

Результаты поиска

Содержание WALLACE & TIERNAN DEOX/2000

Отзывы:

Похожие инструкции для WALLACE & TIERNAN DEOX/2000

Бренды по названию

Популярные бренды