Evoqua WALLACE & TIERNAN DEOX/2000 Скачать руководство пользователя

Страница: 39 / 86

W3T331759 / WT.050.585.003.UE.IM.1014

MICRO/2000® AND DEOX/2000® MODULE

Switch between the basic

displays and trend graphs

• Press the up or down key

Select menu

• Press the “MENU” softkey to select the

• Press the “CAL” softkey to calibrate

• Press the “MODE” softkey to set the

operating mode

Select a menu item in the

menu display

• Select the menu item with the arrow

keys (arrow in front of menu item)

• Confirm the selection with “ENTER”

Change/enter displayed

parameters

• Select the parameter with the arrow

keys (arrow in front of parameter)

• Confirm the selection with “ENTER”

• Change/enter the display with the up or

down arrow keys

• Confirm the entry with “ENTER”

Cancel entry

• Press the “ESC” key to exit the menu

item.

Entries which have not been confirmed

are reset to their original settings.

Reactivate password

protection

This function is only active when a

password has been programmed.

• Change/enter displayed parameters

• Block the system entry with the “LOCK”

softkey in the menu display

Exit the menu item

• Press the “ESC” key

• Press the “BACK” softkey

4.3

Menu Structure

The SFC and MFC have various menus:

•

Main menu

•

Module type, e.g. Cl2 free 1

•

Inputs/Outputs

•

Alarms

•

System

•

Diagnosis

•

Calibration

•

Mode

Display of these depend on the number of sensor measuring modules

installed.

NOTE:

For full menu details refer to manual W3T168777 for SFC and

manual W3T159207 for the MFC.

Содержание WALLACE & TIERNAN DEOX/2000























































































Результаты поиска

Содержание WALLACE & TIERNAN DEOX/2000

Отзывы:

Похожие инструкции для WALLACE & TIERNAN DEOX/2000

Бренды по названию

Популярные бренды

Evoqua WALLACE & TIERNAN DEOX/2000, Инструкция по эксплуатации

Результаты поиска

Содержание WALLACE & TIERNAN DEOX/2000

Отзывы:

Похожие инструкции для WALLACE & TIERNAN DEOX/2000

Бренды по названию

Популярные бренды