manualshive.com logo in svg

Evoqua WALLACE & TIERNAN DEOX/2000, Инструкция по эксплуатации

Поделиться
Скачать
Evoqua WALLACE & TIERNAN DEOX/2000 Скачать руководство пользователя страница 8

W3T331759 / WT.050.585.003.UE.IM.1014

4

MICRO/2000® AND DEOX/2000® MODULE

Electrical Power

During normal operation, the control unit must remain closed. Before 

starting any assembly, inspection, maintenance, or repair work, the 

system must be switched OFF, and the isolator must be secured against 

reactivation. Connect all cables in accordance with the wiring diagram.

Waste Disposal

Ensure  safe  and  environmentally-friendly  disposal  of  reagents  and 

replaced part

Warranty Conditions

The following must be observed for compliance with warranty conditions:

•  

Installation, commissioning by trained and authorized personnel.

•  

Intended use.

•  

Observation of the operational parameters and settings.

•  

The unit may only be operated by trained personnel.

•  

An operating log book must be kept.

•  

Only approved calibration chemicals may be used.

•  

The unit must not be exposed to ambient conditions outside those 

specified.

•  

Maintenance work must be executed at recommended intervals.

•  

Use of original Evoqua Water Technologies spare parts.

If any of the above conditions are not met, the warranty could be void.

Содержание WALLACE & TIERNAN DEOX/2000























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды