background image

W3T331759 / WT.050.585.003.UE.IM.1014

54

MICRO/2000® AND DEOX/2000® MODULE

5.2.8.2  Impeller Shaft Installation

1.   If the impeller shaft coupling is removed from the impeller motor install 

the coupling on the motor shaft against the front face of the motor. 

Tighten the retaining setscrew (using a 3/32-inch Allen wrench).

2.   Slide the impeller shaft into the coupling until it bottoms against the 

end of the motor shaft. Tighten the retaining setscrew snugly (using 

a 3/32-inch Allen wrench), about ¼ turn past the first resistance.

3.   Mount the impeller motor on the back of the panel with the retaining 

screws and washers.

4.   Fasten the impeller motor grounding terminal (with pump motor

 

grounding terminal) on the back of the panel with the retaining 

screw and serrated lockwasher.

5.   Remount the panel in the mounting enclosure.

6.   Reattach the sample and reagent tubing to the inlet of the metering pump.

7.   Apply  a  small  quantity  of  silicone  grease  to  the  O-ring  and 

impeller shaft.

8.   Reinstall the seal adapter, grit guard, cell sealing O-ring, impeller, 

and cell body and cell retaining screws, as described in paragraph 

5.2.6, Impeller Shaft Seal Replacement - Installation of Shaft Seal.

5.2.9  Pump motor removal and replacement

1.   Remove the panel assembly from the mounting enclosure. Refer 

to paragraph 5.2.1, Wetside Panel Removal and Replacement.

2.   Remove the pump rotor and thrust washer from the panel assembly. 

Refer to paragraph 5.2.1, Pump Rotor, Rollers, and Thrust Washer 

Removal and Replacement.

3. 

Disconnect the motor ground lead from the back of the panel.

4.   Remove the two screws that mount the motor from the front of the panel.

5.   Gently slide the motor out from the back of the panel. The motor 

shaft has a sliding fit inside the ball bearing in the pump hub. If it 

binds while trying to slide it out, check the exposed portion of the 

shaft for dirt or scratches that may cause binding. Clean off the 

dirt or carefully remove scratches with a fine file. The shaft can be 

damaged by excessive filing.

Содержание WALLACE & TIERNAN DEOX/2000























































































Отзывы: