manualshive.com logo in svg

Evinrude e-tec 2005, Руководство пользователя

Поделиться
Скачать
Evinrude e-tec 2005 Скачать руководство пользователя страница 51

FREQUENTLY ASKED QUESTIONS

No dealer-scheduled maintenance for the first three years of normal recreational use? Really?

• Yes! Bombardier Motor Corporation of America knows you want to spend your time on the

water, not servicing your 

Evinrude E-TEC

 outboard. There are no valves to adjust, belts to

service, chains to replace, or oil to change. We do recommend pre-launch inspections of
your outboard at each use and at regular intervals. Salt water applications require minimal
additional inspections and lubrication.

What fuel octane is recommended for my 

Evinrude E-TEC

 outboard?

•

Evinrude E-TEC

 outboards require a minimum octane of 87 (U.S.). Use of higher octane fu-

els is not harmful, but also not necessary.

What kind of oil does my 

Evinrude E-TEC

 outboard require?

• Any TC-W3RL oil may be used. The outboard can be programmed by your Dealer to run on

Evinrude/Johnson

 

XD100

 oil for lower oil consumption and reduced operating cost. Refer to

Filling the Oil Tank

 on page 15; see also 

Oil Requirements

 on page 16.

Do I need to mix oil into my fuel?

• No. 

Evinrude E-TEC

 outboards do not require any mixing of oil and fuel.

Where should I take my 

Evinrude E-TEC

 outboard for service?

• For repairs covered under warranty, you must take your 

Evinrude E-TEC

 outboard to an au-

thorized dealer. Bombardier Motor Corporation of America-approved dealers and distribu-
tors have received the necessary training to properly service your outboard. Contact
Bombardier Motor Corporation of America for an authorized 

Evinrude E-TEC

 dealer near

you.

Can I order replacement parts and accessories for my 

Evinrude E-TEC

 outboard?

• Yes. When replacement parts are required, use 

Evinrude/Johnson

 Genuine Parts or parts

with equivalent characteristics, including type, strength, and material. Using substandard
parts could result in injury or product malfunction. Your dealer can order the parts and ac-
cessories you desire.

Do I need to complete any paperwork when I move or sell my 

Evinrude E-TEC

 outboard?

• Yes. In order to maintain contact with you or the new 

Evinrude E-TEC

 owner, Bombardier

Motor Corporation of America requests you complete the form outlining 

Change of Address

/ Change of Ownership

 on page 45. This will ensure you or the new owner is made aware

of any product announcements and keep the warranty coverage up-to-date.

What do I need to do before storing my 

Evinrude E-TEC

 outboard for the winter?

• Winterization is minimal. Refer to 

Storage

 on page 30 for step-by-step instructions to store

your 

Evinrude E-TEC

 outboard for the off-season.

Содержание e-tec 2005





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды