manualshive.com logo in svg

Evinrude e-tec 2005, Руководство пользователя

Поделиться
Скачать
Evinrude e-tec 2005 Скачать руководство пользователя страница 45

43

 C

ALIFORNIA

 E

MISSION

 C

ONTROL

 W

ARRANTY

 S

TATEMENT

YOUR EMISSION CONTROL WARRANTY RIGHTS AND OBLIGATION

The California Air Resources Board and Bombardier Motor Corporation of America (“BMCA”) are pleased
to explain the emission control system warranty on your 2004 

Evinrude E-TEC

 outboard. In California,

new outboard engines must be designed, built, and equipped to meet the State's stringent anti-smog stan-
dards. BMCA must warrant the emission control system on your outboard for the periods of time listed
below provided there has been no abuse, neglect, or improper maintenance of your outboard.

Your emission control system may include parts such as the carburetor or fuel injection system, the igni-
tion system, and catalytic converter. Also included may be hoses, belts, connectors, and other emission-
related assemblies.

Where a warrantable condition exists, BMCA will repair your outboard at no cost to you including diagno-
sis, parts, and labor provided that such work is performed by an authorized BMCA dealer.

Manufacturer's Limited Warranty Coverage

This emission limited warranty covers 

Evinrude

 outboards certified and produced by BMCA for sale in Cal-

ifornia, that are originally sold in California to a California resident, or subsequently warranty-registered to
a California resident. The BMCA U.S. and Canada limited warranty conditions for 

Evinrude

 outboards are

still applicable to these models with the necessary modifications.

Select emission control parts of your 

Evinrude E-TEC

 outboard are warranted from the date of purchase

by the first retail consumer or the date the product is first put to use, whichever occurs first, for a period
of: 4 years, or for 250 hours of use, whichever occurs first.

However, warranty coverage based on the hourly period is only permitted for outboards equipped with the
appropriate hour meters or their equivalent. If any emission-related part on your engine is defective under
warranty, the part will be repaired or replaced by BMCA.

Parts covered are:

1. Electrical System

4. Air Induction System

A. EMM (Engine Management Module)

A. Reed Valves

B. Spark Plugs and Wires

B. Throttle Body Assembly

C. Ignition Coils

C. Intake Manifold

D. Wiring Harness

5. Oil System

2. Exhaust System

A. Oil Injector

A. Inner Exhaust Housing

B. Oil Lines, Fittings, and Clamps

B. Adaptor (Exhaust Manifold)

6. Sensors

3. Fuel System

A. Air Temperature Sensor

A. Fuel Lift Pump

B. Crank Position Sensor

B. Fuel Supply Pump

C. Throttle Position Sensor

C. Fuel Injectors

D. Water Temperature Sensor

D. Vapor Separator

E. Thermostat

E. Fuel Lines, Fittings, and Clamps

7. Gaskets

A. All Emission Component Gaskets

Содержание e-tec 2005





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды