manualshive.com logo in svg

Evinrude e-tec 2005, Руководство пользователя

Поделиться
Скачать
Evinrude e-tec 2005 Скачать руководство пользователя страница 39

37

 A

CCESSORIES

ACCESSORIES

WATER PRESSURE

An optional water pressure gauge is recom-
mended to monitor cooling system pressures.
Noticing changes in water pressure can help
prevent engine overheating. The water pres-
sure gauge must be connected at the correct
point to ensure the most accurate pressure
readings. Follow the installation instructions
included with the water pressure gauge.

1. Water pressure port (behind fuel filter)
2. Fuel filter

PROPELLER

Propeller Selection

To select the correct propeller for your boating
application, your boat and motor MUST be
water tested. See your Dealer for assistance.

IMPORTANT: 

The correct propeller for your

boat, under normal load conditions, will allow
the engine to run near the midpoint of the
RPM operating range at full throttle. Refer to

Specifications

 on page 39.

IMPORTANT: 

Apply 

Triple-Guard

 grease to

the entire propeller shaft before installing the
propeller. At least annually, remove the pro-
peller and check for debris. Clean the shaft
and regrease it before reinstalling a propeller.

Installation

Slide thrust washer onto shaft with shoulder
facing aft.
Slide propeller onto shaft, engaging the
splines and seating it on the thrust bushing.
Slide spacer onto the shaft and engage the
propeller shaft splines.
Wedge a block of wood between the propeller
blade and the anti-ventilation plate.
Install propeller nut and tighten to a torque of
120-144 in. lbs. (13.6-16.3 N·m).
Install keeper on propeller nut, align keeper
slots and cotter pin hole.
Install new cotter pin and bend ends to se-
cure.
Remove block of wood. Make sure engine is
in NEUTRAL; give propeller a spin. It must
turn freely.

Repair

If your propeller hits a solid object, the impact
is partially absorbed by the rubber bushing in
the hub to help prevent damage to the out-
board. A strong impact can damage the hub
and propeller blades. Damage to blades can
cause unusual and excessive vibration. Dam-
age to the hub can cause excessive engine
RPM with little forward movement.

IMPORTANT: 

Avoid or limit operation using a

damaged propeller. Carry a spare propeller.
Keep your propeller in good condition. Use a
file to smooth slight damage to blade edges.
See your Dealer for repair of serious damage.

WARNING

Be alert of people in the water. Always
shift the outboard to NEUTRAL and
shut off the engine immediately when
your boat is in an area where there
might be people in the water. Serious
injury or death can result from contact-
ing a rotating propeller or moving boat
and outboard.

2

1

WARNING

When servicing the propeller, always
shift the outboard to NEUTRAL posi-
tion, turn the key switch OFF, and twist
and remove all spark plug wires so the
outboard cannot be started acciden-
tally.

Содержание e-tec 2005





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды