manualshive.com logo in svg

Evinrude e-tec 2005, Руководство пользователя

Поделиться
Скачать
Evinrude e-tec 2005 Скачать руководство пользователя страница 16

14

   Using Your E-TEC Outboard

ENGINE STOPPING

Twist the throttle grip to SHIFT position or
slower.
Move shift lever to NEUTRAL.
Press the STOP button until the outboard
stops running. If equipped, close the vent
screw on the fuel tank’s filler cap.

1. STOP button

SHIFTING AND SPEED CONTROL

IMPORTANT: 

Carefully check the function of

all control and engine systems before leaving
the dock. DO NOT shift the outboard into
FORWARD or REVERSE while it is shut OFF.

Shifting

With engine running, twist the trottle grip to
SHIFT or slower.
Move the shift lever briskly and decisively to
FORWARD or REVERSE.

1. Shift lever
2. FORWARD
3. REVERSE

IMPORTANT: 

When shifting from FOR-

WARD to REVERSE or from REVERSE to
FORWARD, pause at NEUTRAL until the en-
gine is at idle speed and the boat has slowed.

Speed Control

With the outboard running, twist throttle grip:
• Clockwise to decrease speed; or
• Counterclockwise to increase speed.

1. Decrease speed
2. Increase speed

FUEL SYSTEM PRIMING

FUEL ECONOMY

The economy throttle position can save fuel,
depending on boat load and hull design.
When boat reaches top speed, throttle back
from FULL SPEED. You will save fuel with a
minimal loss of speed.

1

3

2

1

WARNING

Do not operate the outboard in
REVERSE with the tilt/run lever in TILT.
The outboard may tilt out of the water,
resulting in loss of control.

If the outboard is run out of fuel, refill the fuel
tank and squeeze the primer bulb until firm.
Prime the electric fuel pump by first removing
the emergency stop switch clip and then pull-
ing the rope at least two times. This will cause
the fuel pump to fill the injectors. Replace the
emergency stop switch clip and follow the
normal starting procedure.

2

1

Содержание e-tec 2005





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды