manualshive.com logo in svg

Evinrude e-tec 2005, Руководство пользователя

Поделиться
Скачать
Evinrude e-tec 2005 Скачать руководство пользователя страница 15

13

 S

TARTING

, S

TOPPING

, S

HIFTING

Move the shift lever to NEUTRAL. Refer to

Shifting and Speed Control

 on page 14.

1. NEUTRAL

Twist throttle grip to SHIFT or slower.

1. SHIFT

While seated, grasp the starter handle and
pull slowly until the starter engages, then pull
hard. Repeat, if needed, until outboard starts.
To prevent damage to starter assembly, allow
starter cord to rewind before releasing starter
handle.

1. Starter handle
2. NEUTRAL

If your outboard does not react normally to
this starting procedure or if it fails to start, re-
fer to 

Troubleshooting

 on page 33.

After Engine Starts

Check the water pump indicator. A steady
stream of water indicates the water pump is
working. If a steady stream of water from the
water pump indicator is not visible, stop the
engine. Refer to 

Engine Overheating

 on

page 21.

WARNING

Always shift to NEUTRAL before start-
ing the outboard to prevent sudden
boat movement, which can cause
injury.

DO NOT

 advance the throttle before start-up.

Advancing the throttle overrides the electron-
ic idle control system. After the engine starts,
the engine management module (

EMM

) au-

tomatically increases idle speed slightly. Idle
speed will decrease as the engine warms up.
If the outboard is started at wide open throt-
tle, twist the throttle grip back to SHIFT be-
fore shifting.

1

1

1

2

1

Содержание e-tec 2005





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды