manualshive.com logo in svg

Evinrude e-tec 2005, Руководство пользователя

Поделиться
Скачать
Evinrude e-tec 2005 Скачать руководство пользователя страница 23

21

 O

PERATION

ENGINE OVERHEATING

IMPORTANT: 

Do not run your outboard—

even for a brief start-up—without supplying
water to it. Refer to 

Flushing

 on page 30.

While boating, the outboard’s water intakes
must stay completely submerged and unob-
structed. Observe proper transom height and
tilt angle. While the outboard is running, the
outboard’s water pump indicator must dis-
charge a steady stream of water. Check the
indicator often, especially when operating in
weeds, muddy and debris-laden water, and at
extreme trim angles.

1. Water intake screens
2. Water pump indicator

If the engine overheats, the 

S.A.F.E.

 (Speed

Adjusting Failsafe Electronics) mode will im-
mediately limit the engine’s speed to 1200
RPM. If the engine was running faster than
1200 RPM when the 

S.A.F.E.

 mode activat-

ed, it will shake noticeably. The protection
system must be 

RESET

 before the engine will

operate at speeds over 1200 RPM. Under
certain conditions the 

EMM

 will shut off the

engine.

WARNING

Always use the safety lanyard when
operating your boat to help prevent a
runaway boat and reduce the risk of
personal injury or death.

Avoid knocking or pulling the clip off
the stop switch during normal boating.
The resulting unexpected loss of for-
ward motion can throw occupants for-
ward, causing injury.

Your emergency stop switch can be
effective only when in good working
condition. At each outing, inspect clip
and lanyard for cuts, breaks, or wear.
Replace worn or damaged parts. Keep
the lanyard free from obstructions and
entanglements. At each outing, test the
system’s operation. With the engine
running, remove the clip from the
switch by pulling the lanyard. If the
engine does not stop running, see your
Dealer.

To RESET the system:
• The engine must be shut off and the cooling

temperature restored.

IF

 the 

S.A.F.E.

 mode activates and the

stream from the water pump indicator be-
comes intermittent or stops, reduce speed to
idle and:
1) Shift to NEUTRAL.
2) SHUT OFF the engine.
3) Tilt the outboard up.
4) Clean the intake screens of any blockage.
5) Clean the water pump indicator of any

blockage.

6) Lower the outboard.
7) Restart the engine and run at idle.

IF

 cleaning the screens and indicator 

does

not

 restore the water pump indicator’s steady

discharge, the engine will operate only in “get
home” mode. Return to harbor immediately.
See your Dealer.

IF

 cleaning the screens and indicator 

does

restore the water pump indicator’s steady
discharge, you might have to run for two min-
utes in NEUTRAL to allow the engine to cool.

IMPORTANT: 

If cooling is not restored, the

EMM

 will identify a progressive overheating

condition and shut off the engine. The engine
will not restart until the engine is allowed to
cool.
After any overheat causing engine shutdown,
see your Dealer for:
• Inspection of the water pump for excessive

wear or damage.

• Inspection of the thermostats.

IMPORTANT: 

Although the 

S.A.F.E.

 mode

can help prevent engine damage, it does not
guarantee you can run your engine indefinite-
ly without engine damage.

Содержание e-tec 2005





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды