manualshive.com logo in svg

Evinrude e-tec 2005, Руководство пользователя

Поделиться
Скачать
Evinrude e-tec 2005 Скачать руководство пользователя страница 31

29

 M

AINTENANCE

 S

CHEDULE

MAINTENANCE SCHEDULE

Routine maintenance is necessary for all mechanized products. Periodic maintenance contrib-
utes to the product’s life span. The following maintenance chart provides guidelines for out-
board maintenance and inspection scheduled to be performed by an authorized Dealer. The
schedule should be adjusted according to operating conditions and use.
The recommended lubricants have been formulated to protect bearings, gears and engine
components. They must be used to avoid damage caused by improper lubrication.

Description

Engine 

Care 

Product

Every 300 

Hours or 

Three Years

(1)

(1)  When used in normal recreational use. Common sense dictates when using an 

Evinrude E-TEC

 

outboard for commercial or other heavy use that you check these items more frequently (annual 

checks are recommended).

Electrical and ignition wires, inspect for wear or chafing

Engine to transom mounting hardware, re-torque (40 ft. lbs.)

Fasteners, inspect any loosened components

Fuel and oil system components, inspect and repair leaks 

(2)

(2) Emission-related 

component

Fuel filter, replace

Gearcase lubricant, replace

A

Grease fittings, lubricate 

(3)

(3)  Annually in salt water applications – Refer to 

Salt Water Lubrication Points

 on page 23

Muffler foam, inspect and replace if necessary

Propeller shaft splines, inspect and lubricate 

(3)

B

Spark plugs, inspect and replace if necessary 

(2)

Steering handle, inspect and lubricate

B

Thermostats, inspect 

(2)

Throttle cable, inspect and re-tension

Water pump, inspect or replace if necessary

A.

 

Ultra-HPF

 gearcase lubricant

B. 

Triple Guard

 grease

Содержание e-tec 2005





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды