manualshive.com logo in svg

Evinrude e-tec 2005, Руководство пользователя

Поделиться
Скачать
Evinrude e-tec 2005 Скачать руководство пользователя страница 25

23

 O

PERATION

SALT WATER

Additional anodic protection for the outboard
has been provided for use in salt or brackish
water.
Upon removal from salt water, leave outboard
in a vertical position until its cooling system
has drained. During long periods of mooring,
tilt the gearcase out of the water, except in
freezing temperatures. Flush the outboard, if
desired. Refer to 

Flushing

 on page 30.

Salt Water Lubrication Points

1. Tilt lever, tilt lever shaft, and swivel bracket lu-

brication points (annually)

1. Tilt tube lubrication points (annually)

Anti-Corrosion Anodes

Your outboard is equipped with one or more
anodes that protect it from galvanic corrosion.
Disintegration of the anode is normal and in-
dicates it is working. Check each anode peri-
odically. Replace anodes smaller than 2/3
their original size. See your Dealer for re-
placements.

Galvanic corrosion destroys underwater met-
al parts and can occur in fresh or salt water;
however, salt, brackish, and polluted waters
will accelerate corrosion.
Metal-based antifouling paint on the boat or
outboard and the use of improperly installed
shore power in the area of your moored boat
will also accelerate corrosion.

IMPORTANT: 

NEVER paint the anode, its

fasteners, or its mounting surface. Painting
will reduce its corrosion protection.

WEEDY WATER

Weeds block water intakes and may cause
your outboard to overheat. Weeds on the pro-
peller create vibration and reduce boat speed.
When operating in weedy water, run at slow
speeds and in REVERSE frequently to clear
weeds from the propeller and water intakes.
Check the water pump indicator often.
If REVERSE operation does not clear away
weeds, SHUT OFF the engine. Remove
weeds from propeller area and water intakes
before operating at higher speed.

1

1

Содержание e-tec 2005





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды