EURA E2000-0004 S2B, Инструкции по безопасности и руководство по эксплуатации

Страница: 26 / 82

4) Electrical connections of E2000+ inverters
Control terminal function and factory default configuration
Main terminal
Terminal Type
DO1
/D
ig
it
a
l
DO2
TA TB
an
alo
g
u
e
TC
outputs
AO1
Related
Description Hardware data parameter DEFAULT setting
Programmable Open-Collector output, max. 100mA-24V
(F301) (F303) Message F=>0Hz
digital output 1 (referred on CM)
– Pulse output
Programmable Open-Collector output, max. 100 mA-
(F302) Message F>0HZ
digital output 2 24V (referred on CM)
TC=COMMON TB=NORMAL CLOSED
Digital Relays TA=NORMAL OPEN
output - isolated Max. Contact load: Inverter 22 kW and (F300) Fault signal
switchover contact below: 2A/230VAC - above 22 kW:
5A/230V
Programmable
To configure for voltage/current signal
(F413---F426) Output frequency
(reference: analogue ground GND)
analogue output 1 (F431)
0…10V
For current signal: set SWITCH to „I“
AO2
10V
10
V
DC
AI1
In
p
u
ts
-A
nalo
gue
AI2
Programmable Current signal 0(4)...20 mA (reference
analogue output 2 analogue ground GND) >22kW only
10V, referred on 10V supply for potentiometer or similar,
analogue ground max. current 20 mA
Set-point
– current/voltage input
Programmable
for configuration see: (Hardware and
analogue input 1
configuration of I/O channels)
Set-point
– current/voltage input
Programmable
for configuration see: (Hardware and
analogue input 2
configuration of I/O channels)
----(F427F430) Motor current
(F432) 0... 20mA
(F400-F405)
0…10V
(F418)
(F406-F411)
0..20 mA
(F419)
GND
24V
DC
24V
Analogue ground
Microprocessor ground, reference point
for all analogue signals
Isolated 24V power
24±1.5V, to CM; limited to 50mA, for
supply powering of digital I/Os
DI1
DI2
DI3
DI4
DI5
DI6
DI7
DI8
Pr
o
g
ramm
ab
le
d
ig
ita
l i
n
p
u
ts
Programmable
digital input 1
Programmable
digital input 2
Programmable
digital input 3
Programmable
digital input 4
Programmable
digital input 5
Programmable
digital input 6
Programmable
digital input 7
Programmable
digital input 8
HIGH/LOW active (NPN/PNP) selectable
via hardware - see: (Hardware and
(F316)
configuration of I/O channels)
Pulse signal input
(F317)
(F318)
HIGH/LOW active (NPN/PNP) selectable
(F319) via hardware - see: (Hardware and
configuration of I/O channels)
(DI7
– DI8 on inverters above 22 kW only
(F320)
All digital I/O are floating, including 24V
(F321)
supply and CM
(F322)
(F323)
Jog mode FWD
Emergency stop
external signal
Terminal (FWD)
Terminal (REV)
RESET
Power stage
enable
START
STOP
CM
COMM
Common for digital Common for digital inputs and 24V aux.
I/O supply
RS485 Terminal
GND
Analogue ground
Microprocessor ground, reference point
for all analogue signals
R S
+5V 5V, 50 mA 5 V supply microprocessor level
A+
4 8 5
Differential signal, Standard: TIA/EIA-485(RS-485)
positive Interface protokol: MODBUS
(F900-F904) 9600
Bd.Rate: 1200/2400/4800/9600/19200/
Differential signal,
B- negative 38400/57600