Epson S1C17M12 Скачать руководство пользователя

Страница: 213 / 253

18 Multiplier/Divider (COPRO2)

S1C17M12/M13 TECHNICAL MANUAL

Seiko Epson Corporation

18-7

(Rev. 1.2)

Conditions to set the overflow (V) flag

An overflow occurs in a signed MAC operation and the overflow (V) flag is set to 1 when the signs of the mul-

tiplication result, operation result register value, and multiplication & accumulation result match the following

conditions:

Table 18.5.3 Conditions to Set the Overflow (V) Flag

Mode setting value

Sign of multiplication result

Sign of operation result

register value

Sign of multiplication &

accumulation result

0x07

0 (positive)

1 (negative)

0x07

1 (negative)

0 (positive)

An overflow occurs when a MAC operation performs addition of positive values and a negative value results,

or it performs addition of negative values and a positive value results. The coprocessor holds the operation re-

sult until the overflow (V) flag is cleared.

Conditions to clear the overflow (V) flag

The overflow (V) flag that has been set will be cleared when an overflow has not been occurred during execu-

tion of the “

ld.ca

” instruction for MAC operation or when the “

ld.ca

” or “

ld.cf

” instruction is executed

in an operation mode other than operation result read mode.

18.6 Reading Operation Results

The “

ld.ca

” instruction cannot load a 32-bit operation result to a CPU register, so a multiplication, division or

MAC operation returns the one-half (16 bits according to the output mode) result (A[15:0] or A[31:16]) and the

flag status to the CPU registers. Another one-half should be read by setting COPRO2 into operation result read

mode. The operation result register keeps the loaded operation result until it is rewritten by other operation.

16 bits

S1C17 Core

Operation result

Selector

Argument 2

Argument 1

Coprocessor

output (16 bits)

Flag output

COPRO2

Figure 18.6.1 Data Path in Operation Result Read Mode

Table 18.6.1 Operation in Operation Result Read Mode

Mode set-

ting value

Instruction

Operations

Flags

Remarks

0x03

ld.ca %rd,%rs

%rd

←

res[15:0]

psr (CVZN)

←

0b0000 This operation mode does not

affect the operation result reg-

isters 0 and 1.

ld.ca %rd,imm7

%rd

←

res[15:0]

0x13

ld.ca %rd,%rs

%rd

←

res[31:16]

ld.ca %rd,imm7

%rd

←

res[31:16]

0x23

ld.ca %rd,%rs

%rd

←

res1[15:0]

ld.ca %rd,imm7

%rd

←

res1[15:0]

0x33

ld.ca %rd,%rs

%rd

←

res1[31:16]

ld.ca %rd,imm7

%rd

←

res1[31:16]

res0: operation result register 0, res1: operation result register 1

Содержание S1C17M12






























































































































































































































































Результаты поиска

Содержание S1C17M12

Отзывы:

Похожие инструкции для S1C17M12

Бренды по названию

Популярные бренды

Epson S1C17M12, Техническое руководство

Результаты поиска

Содержание S1C17M12

Отзывы:

Похожие инструкции для S1C17M12

Бренды по названию

Популярные бренды