Epson R320 - Stylus Photo Color Inkjet Printer Скачать руководство пользователя страница 45

Страница: 45 / 114

EPSON Stylus Photo R320

Revision B

DISASSEMBLY AND ASSEMBLY

Disassembly

2.3.6 Removing Panel Board

External View

Figure 2-14. Removing "Panel Board"

Parts/Units which should be removed before removing "Panel Board"

Paper Support Assy./Preview Monitor Unit/Housing, Upper

Procedure for Removing

Remove the screws (x4) which secure "Board Assy., Panel". Then, remove
"Board Assy., Panel".

Remove the screw which secures "Panel Board". Then, remove "Panel Board"
from "Shield Plate, LCD".

Take off the two-sided tapes (x2) which secure "Cover, LCD" from the back
of "Housing, Upper". Then, remove "Cover, LCD".

C.B.P 3x8

(5-7kgf•cm)

Board Assy., Panel

Line Mark

Cover, LCD

Two-sided

Tapes

Switch

Panel Board

LCD Panel

Rib and

Adjusting Hole

Shield Plate, LCD

C.B.S 3x6 (4-6kgf•cm)

C A U T I O N

Do not damage "LCD Panel".

When removing "Panel Board Unit", the switch may detach and
drop. If this occurs, reinstall it referring the figure.

When looking at back side of "Housing, Upper", make sure that
the line mark of "Housing, Upper" securely comes to the position
shown in the figure.

Match the rib of "Shield Plate, LCD" and the positioning hole of
"Panel Board".

Screw "Board Assy., Panel" in the order as shown in the figure.

Содержание R320 - Stylus Photo Color Inkjet Printer



















































































































Результаты поиска

Содержание R320 - Stylus Photo Color Inkjet Printer

Отзывы:

Похожие инструкции для R320 - Stylus Photo Color Inkjet Printer

Бренды по названию

Популярные бренды

Epson R320 - Stylus Photo Color Inkjet Printer, Руководство по обслуживанию

Результаты поиска

Содержание R320 - Stylus Photo Color Inkjet Printer

Отзывы:

Похожие инструкции для R320 - Stylus Photo Color Inkjet Printer

Бренды по названию

Популярные бренды