Epson R320 - Stylus Photo Color Inkjet Printer Скачать руководство пользователя страница 68 | Manualshive

Страница: 68 / 114

background image

EPSON Stylus Photo R320

Revision B

DISASSEMBLY AND ASSEMBLY

Disassembly

68

C A U T I O N

When lifting up "Printer Mechanism", "Lever, Change" and
"Combination Gear, 27.2, 19.2" may detach and drop. Take care
not to drop and damage them.

When lifting up "Printer Mechanism", take care not to leak and
drip ink from the end of "Waste Ink Tube" ("Waste Ink Pads"
side).

To prevent "Frame, Main" from warping, do not lift "Printer
Mechanism" holding the places other than specified.

W A R N I N G

When installing "Printer Mechanism" to "Housing, Lower", pass
"Waste Ink Tube" through the hook indicated in the figure below,
and securely set it in the groove, so that "Porous Pad, Ink Eject,
Upper, Support" will not lift up above the tube. If installed
insecurely, it may cause the ink leakage.

Figure 2-46. Reinstalling "Waste Ink Tube"

Waste Ink Tube

Porous Pad, Ink Eject, Upper, Support

Hook

Reinstalling "Printer Mechanism"

For this printer, "Housing, Lower" is the standard to
correctly install each part of "Printer Mechanism".
In order to ensure the accuracy for installing, it is necessary
to manage the reference position for "Frame, Main"
installation in X, Y and Z direction as shown in the figure
below. If every part is set correctly, "Printer Mechanism"
can be secured with the hooks (x4).

[X-axis]
• Make sure that "Frame, Main" is installed correctly to the

groove of "Housing, Lower".

• Make sure that there is no gap between "Frame, Main"

and "Housing, Lower".

[Y-axis]
Make sure that the slot of "Frame, Main" is correctly
installed to the projection of "Housing, lower".
[Z-axis]
• Make sure that there is no gap between "Frame, Main"

and "Housing, Lower"

• Make sure that the left side of "Printer Mechanism" is

correctly secured with the hooks (x2).

Figure 2-47. Reference position for installing "Frame, Main"

Left

Hooks

Right

Hooks

X-axis :

(4 points)

Y-axis :

(1 point)

Z-axis :

(4 points)

«
...
66
67
68
69
70
...
»

Содержание R320 - Stylus Photo Color Inkjet Printer



















































































































Отзывы:

Нет отзывов

Похожие инструкции для R320 - Stylus Photo Color Inkjet Printer

Бренд: Canon Страницы: 29

Бренд: Canon Страницы: 65

Бренд: Canon Страницы: 2

Sure shot 80 tele

Бренд: Canon Страницы: 39

BJC6500 - BJC 6500 Color Inkjet Printer

Бренд: Canon Страницы: 6

Бренд: Canon Страницы: 20

imagePROGRAF iPF6450

Бренд: Canon Страницы: 35

PIXMA MX340 Series

Бренд: Canon Страницы: 11

imagePROGRAF iPF6300S

Бренд: Canon Страницы: 12

Бренд: Canon Страницы: 19

iP4700 - PIXMA Color Inkjet Printer

Бренд: Canon Страницы: 28

Бренд: Canon Страницы: 2

Бренд: Canon Страницы: 35

Бренд: Canon Страницы: 52

Laser Class 810

Бренд: Canon Страницы: 322

Бренд: DataCard Страницы: 17

Бренд: DataCard Страницы: 24

Бренд: LabelTac Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды