Epson R320 - Stylus Photo Color Inkjet Printer Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 114

background image

EPSON Stylus Photo R320

Revision B

TROUBLESHOOTING

Troubleshooting with LED/LCD Indications and Status Monitor 3 Message

9

1.2 Troubleshooting with LED/LCD Indications and Status Monitor 3 Message

This section describes the LED/LCD indication, the STM3 message and the error condition when the printer detects an error in each operation such as the power on, the paper
loading/feeding and the ink absorption operation.

Table 1-3. LED/LCD Indication and STM3

Printer status

Maintenance

LED indication

LCD indication

STM3 message

Condition for error detection

Communication Error

--

--

This error is detected when the printer cannot
communicate with the PC properly.

Ink Low Condition

Blink

(Ink icon blinks)

Note :
Printing operation can be performed until it becomes ink
end condition even after the error message is displayed on
STM3. However, the Head Cleaning operation may not be
performed due to the Ink Low condition.

This error is detected when the ink consumption
reaches about 90%.

(Note)
When the Ink Low Condition is detected, the
Maintenance LED will blink. The printer will
continue to keep this LED status even if a new
Ink Cartridge is installed in the Ink Cartridge
replacement position. However, this LED status
will be reset (LED off) when "Carriage Unit"
returns to the home position.

«
...
7
8
9
10
11
...
»

Содержание R320 - Stylus Photo Color Inkjet Printer



















































































































Отзывы:

Нет отзывов

Похожие инструкции для R320 - Stylus Photo Color Inkjet Printer

Бренд: KARPO Fly Страницы: 13

Бренд: Dakota Digital Страницы: 2

Бренд: Dakota Digital Страницы: 6

Бренд: Dakota Digital Страницы: 7

Бренд: Dakota Alert Страницы: 2

Бренд: Fantasea Страницы: 18

Бренд: Fantasea Страницы: 15

AdvancedPunch Pro

Бренд: GBC Страницы: 92

Бренд: LAS Страницы: 44

Бренд: LAS Страницы: 24

Бренд: Raven Страницы: 70

Бренд: Tait Страницы: 10

Powersaver Dual Flexi

Бренд: Sangamo Страницы: 2

WORKCENTER 5222

Бренд: Xerox Страницы: 28

VersaLink C7000

Бренд: Xerox Страницы: 2

WorkCentre 6505

Бренд: Xerox Страницы: 4

Бренд: Xerox Страницы: 4

Бренд: Xerox Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды