Epson R320 - Stylus Photo Color Inkjet Printer Скачать руководство пользователя страница 33

Страница: 33 / 114

EPSON Stylus Photo R320

Revision B

DISASSEMBLY AND ASSEMBLY

Overview

2.1.2 Tools

Use only specified tools to avoid damaging the printer.

2.1.3 Pre-Shipment Checks

When returning this product to the user after servicing, check that the work is complete
using the following table.

Table 2-1. Tools

Tool Name

Supplier

Code

Phillips Screw Driver (No. 0)

EPSON

1080531

Phillips Screw Driver (No. 1)

EPSON

1080530

Phillips Screw Driver (No. 2)

EPSON

1080532

Tweezers

EPSON

1080561

Acetate Tape

EPSON

1003963

Table 2-2. Service Completion Pre-Shipment Check List

Classification

Item

Check Point

Status

Main Unit

Self-test

Is the operation normal?

Checked

Not necessary

On-line Test

Is the printing successful?

Checked

Not necessary

Print Head

Is ink discharged normally from
all the nozzles?

Checked

Not necessary

Carriage
Mechanism

Does it move smoothly?

Checked

Not necessary

Is there any abnormal noise
during its operation?

Checked

Not necessary

Is there any dirt or foreign
objects on the CR Guide Shaft?

Checked

Not necessary

Is the CR Motor at the correct
temperature?
(Not too heated?)

Checked

Not necessary

Paper Feeding
Mechanism

• Is paper fed smoothly?

• No paper jamming?

• No paper skew?

• No multiple feeding?

• No abnormal noise?

Checked

Not necessary

Is the PF Motor at correct
temperature?

Checked

Not necessary

Is the paper path free of any
obstructions?

Checked

Not necessary

Adjustment

Specified
Adjustment

Are all the adjustment done
correctly?

Checked

Not necessary

Содержание R320 - Stylus Photo Color Inkjet Printer



















































































































Результаты поиска

Содержание R320 - Stylus Photo Color Inkjet Printer

Отзывы:

Похожие инструкции для R320 - Stylus Photo Color Inkjet Printer

Бренды по названию

Популярные бренды

Epson R320 - Stylus Photo Color Inkjet Printer, Руководство по обслуживанию

Результаты поиска

Содержание R320 - Stylus Photo Color Inkjet Printer

Отзывы:

Похожие инструкции для R320 - Stylus Photo Color Inkjet Printer

Бренды по названию

Популярные бренды