Epson R320 - Stylus Photo Color Inkjet Printer Скачать руководство пользователя страница 75

Страница: 75 / 114

EPSON Stylus Photo R320

Revision B

DISASSEMBLY AND ASSEMBLY

Disassembly

External View

Figure 2-56. Removing "Ink System" (2)

Remove "Extension Spring, 0.441" from the hooks of "Slider, Cap" and
"Frame, Cap" by using the tweezers.

10. Remove "Extension Spring, 0.788" from the hooks of "Lever, Lock, Slider"

and "Frame, Cap" by using the tweezers.

11. Remove the shaft of "Slider, Cap" from the slot of "Frame, Cap", then remove

"Lever, Lock, Slider".

12. Remove "Porous, Slider, Cap" from the hook of "Slider, Cap".

Extension

Spring, 0.788

Extension

Spring, 0.441

Hooks

Frame, Cap

Slider, Cap

Shaft

Porous Pad, Slider, Cap

Hook

Lever, Lock, Slider

Reinstalling "Lever, Lock, Slider"

Check if it works properly with "Slider, Cap".

Reinstalling "Ink System"

Make sure that the ink tube is correctly connected to the
point of "Frame, Cap" shown in the figure below. If it is not
connected properly, it may cause ink leakage.

Figure 2-57. Connecting Point for the ink tube

Do not touch the sealing rubber part and "Cleaner Head".

Make sure that the line mark of the ink tube is not twisted.

Check if "Cap Assy." moves smoothly.

Содержание R320 - Stylus Photo Color Inkjet Printer



















































































































Результаты поиска

Содержание R320 - Stylus Photo Color Inkjet Printer

Отзывы:

Похожие инструкции для R320 - Stylus Photo Color Inkjet Printer

Бренды по названию

Популярные бренды

Epson R320 - Stylus Photo Color Inkjet Printer, Руководство по обслуживанию

Результаты поиска

Содержание R320 - Stylus Photo Color Inkjet Printer

Отзывы:

Похожие инструкции для R320 - Stylus Photo Color Inkjet Printer

Бренды по названию

Популярные бренды