Epson R320 - Stylus Photo Color Inkjet Printer Скачать руководство пользователя страница 41

Страница: 41 / 114

EPSON Stylus Photo R320

Revision B

DISASSEMBLY AND ASSEMBLY

Disassembly

2.3.4 Removing Housing, Middle

External View

Figure 2-6. Removing "Housing, Middle"

Parts/Units which should be removed before removing "Housing, Middle"

Paper Support Assy./Preview Monitor Unit/Housing, Upper

Procedure for Removing

Pull out "Panel FFC" from "Ferrite Core".

Take off the two-sided tape which fixing the "Panel FFC" from "Housing
Middle".

Remove the screw which secures "Cover, Ink Tube", release the hook and
then remove "Cover, Ink Tube".

Remove the screws (x4) which secure "Housing, Middle".

Lay down the printer backward, put a flat-blade screwdriver or alike into the
slot located on the bottom surface of "Housing, Lower" and then release the
hooks (x2) which secure "Housing, Middle".

Lift "Housing, Middle" upward and remove it.

Fixed spring, Core

C.B.P 3x8

(4-6kgf•cm)

Panel FFC

Two-sided

Tape

Ferrite Core

C.B.S 3x8 (6-8kgf•cm)

Housing, Middle

C.B.P 2.5x8
(3-5kgf•cm)

Hook

Cover, Ink Tube

C.B.P 3x8

(4-6kgf•cm)

C.B.S 3x10

(4-6kgf•cm)

Slots and Hook

Housing, Lower

C A U T I O N

Do not damage the hooks of "Housing, Middle" with the flat-blade
screwdriver or alike.

Through the "Monitor FFC" into the hole on "Housing Middle".

Figure 2-7. Reinstalling "Housing, Middle"

Hole

Monitor FFC

Содержание R320 - Stylus Photo Color Inkjet Printer



















































































































Результаты поиска

Содержание R320 - Stylus Photo Color Inkjet Printer

Отзывы:

Похожие инструкции для R320 - Stylus Photo Color Inkjet Printer

Бренды по названию

Популярные бренды

Epson R320 - Stylus Photo Color Inkjet Printer, Руководство по обслуживанию

Результаты поиска

Содержание R320 - Stylus Photo Color Inkjet Printer

Отзывы:

Похожие инструкции для R320 - Stylus Photo Color Inkjet Printer

Бренды по названию

Популярные бренды