Epson R320 - Stylus Photo Color Inkjet Printer Скачать руководство пользователя страница 25

Страница: 25 / 114

EPSON Stylus Photo R320

Revision B

TROUBLESHOOTING

Unit Level Troubleshooting

Table 1-12. Check Points When More Than One Paper is Fed Constantly Without LED/STM3's Error Notifications

Occurrence Timing

Position of CR

Phenomenon Detail

Faulty Part/

Part Name

Check Point

Remedy

At operation

The printer always feeds more than one
sheet of paper at a time without LED/
STM3's error notifications.

ASF Assy.

1. Check if "Roller, Retard Assy." works correctly while

feeding paper.

1. Reassemble "Extension Spring, 0.45" on the

back of "Roller, Retard Assy."

Extension Spring,

0.45

Table 1-13. Check Points for Abnormal Sound

Occurrence Timing

Position of CR

Phenomenon Detail

Faulty Part/

Part Name

Check Point

Remedy

Any time

Anywhere

Makes abnormal sound in spite of the
normal print operation at the first power
on or some other time.

Carriage Unit

1. Check if there is enough grease on "CR Guide Shaft".

1. Wipe the remaining grease off on "CR Guide

Shaft" and then lubricate it.

Ink System

1. Check if "Lever, Change" moves smoothly.

1. Replace "Ink System" with a new one.

The bottom of "Carriage Unit" touches
the surface of "Front Frame".

Frame EJ Assy.

1. Check if "Frame EJ Assy." is not warping upward.

1. Replace "Frame EJ Assy." with a new one.

"Carriage Unit" strikes on "Paper Guide,
Upper" while "Carriage Unit" is
working.

Paper Guide,

Upper

1. Check if "Paper Guide, Upper" has come off from "Main

Frame".

1. Reassemble "Paper Guide, Upper" to "Main

Frame".

Содержание R320 - Stylus Photo Color Inkjet Printer



















































































































Результаты поиска

Содержание R320 - Stylus Photo Color Inkjet Printer

Отзывы:

Похожие инструкции для R320 - Stylus Photo Color Inkjet Printer

Бренды по названию

Популярные бренды

Epson R320 - Stylus Photo Color Inkjet Printer, Руководство по обслуживанию

Результаты поиска

Содержание R320 - Stylus Photo Color Inkjet Printer

Отзывы:

Похожие инструкции для R320 - Stylus Photo Color Inkjet Printer

Бренды по названию

Популярные бренды