Epson R320 - Stylus Photo Color Inkjet Printer Скачать руководство пользователя страница 12

Страница: 12 / 114

EPSON Stylus Photo R320

Revision B

TROUBLESHOOTING

Troubleshooting with LED/LCD Indications and Status Monitor 3 Message

CD/DVD Guide Error

Close the CD/DVD guide.

This error is detected when ;

1. Paper is present in "ASF Assy.", and "CDR

Guide Assy." is open while receiving print
data.

2. "CDR Guide Assy." opens while printing.

3. "CDR Guide Assy." is open while receiving

ASF paper feed data.

4. Attempting to replace the ink while "CDR

Guide Assy." is open.

CD/DVD Tray Error

The CD/DVD tray load error. Reload
tray and press Maintenance.

This error is detected when "CD/DVD Tray"
cannot be detected when printing CD/DVD.

Memory Card Error

(Non supported

Memory Card)

The inserted card cannot be used with
this printer.

No Display

This error is detected when nonstandardized
Memory Card is inserted.

Bluetooth Module Error

Bluetooth Photo Print Adapter error.
Disconnect the Adapter from the
printer, then reconnect it.

No Display

This error is detected when there is no response
from Bluetooth Module.

Irregular external device

Blink

The connected device cannot be used.
(The warning is displayed for one
second every 3 seconds.)

No Display

This error is detected when some non supported
device is connected to the port for the external
memory device.

Table 1-3. LED/LCD Indication and STM3

Printer status

Maintenance

LED indication

LCD indication

STM3 message

Condition for error detection

Содержание R320 - Stylus Photo Color Inkjet Printer



















































































































Результаты поиска

Содержание R320 - Stylus Photo Color Inkjet Printer

Отзывы:

Похожие инструкции для R320 - Stylus Photo Color Inkjet Printer

Бренды по названию

Популярные бренды

Epson R320 - Stylus Photo Color Inkjet Printer, Руководство по обслуживанию

Результаты поиска

Содержание R320 - Stylus Photo Color Inkjet Printer

Отзывы:

Похожие инструкции для R320 - Stylus Photo Color Inkjet Printer

Бренды по названию

Популярные бренды