Epson R320 - Stylus Photo Color Inkjet Printer Скачать руководство пользователя страница 53

Страница: 53 / 114

EPSON Stylus Photo R320

Revision B

DISASSEMBLY AND ASSEMBLY

Disassembly

2.3.10 Removing Holder, Shaft Assy.

External View

Figure 2-25. Removing "Holder, Shaft Assy." (1)

Parts/Units which should be removed before removing "Holder, Shaft Assy."

Paper Support Assy./Preview Monitor Unit/Housing, Upper/Housing, Middle/
Main Board Unit/
ASF Assy.

Procedure for Removing

Move "Carriage Unit" toward 80-digits Side.

Remove the screws (x2) which secure "Holder, Shaft Assy.".

Pull "Holder, Shaft Assy." upward and release the hooks (

: x2) with the

tweezers or alike. Then, Release the dowel from "Ink System Frame".

Looking at the printer from its back side, press down "Paper Guide, Upper" on
the left, and release "PE Sensor Lever" from the slot. Remove "Holder, Shaft
Assy." by sliding it to the right.

Release "Cable, Head" from the hooks (

: x7) of "Holder, Shaft Assy.".

Carriage Unit

80-digits Side

Cable, Head

Ribs

Holder, Shaft Assy.

Dowel

PE Sensor Lever

Paper Guide,

Upper

C.B.S 3x6

(6-8kgf•cm)

C A U T I O N

Be careful not to damage "PE Sensor Lever" and "Paper Guide,
Upper" when removing them since "PE Sensor Lever" contacts
with "Paper Guide, Upper".

C A U T I O N

Do not damage "Cable, Head".

Содержание R320 - Stylus Photo Color Inkjet Printer



















































































































Результаты поиска

Содержание R320 - Stylus Photo Color Inkjet Printer

Отзывы:

Похожие инструкции для R320 - Stylus Photo Color Inkjet Printer

Бренды по названию

Популярные бренды

Epson R320 - Stylus Photo Color Inkjet Printer, Руководство по обслуживанию

Результаты поиска

Содержание R320 - Stylus Photo Color Inkjet Printer

Отзывы:

Похожие инструкции для R320 - Stylus Photo Color Inkjet Printer

Бренды по названию

Популярные бренды