Epson R320 - Stylus Photo Color Inkjet Printer Скачать руководство пользователя страница 15

Страница: 15 / 114

EPSON Stylus Photo R320

Revision B

TROUBLESHOOTING

Unit Level Troubleshooting

Table 1-5. Check Points for Error Before the Initial Ink Charge, Error Before Ink Cartridge Replacement Cleaning and No Ink Cartridge Error

Occurrence Timing

Position of CR

Phenomenon Detail

Faulty Part/

Part Name

Check Point

Remedy

At power-on

At HP

The printer does not perform the Initial
Ink Charge and the error is displayed on
LED and STM3.

Ink Cartridge

1. Check if the Ink Cartridge is normal by installing it in

another printer.

1. Replace the Ink Cartridge with a new one.

Main Board

1. Check if the correct data has been written in the address

5B<H> of EEPROM on "Main Board".
(You cannot check it only with the Adjustment Program
of Stylus Photo R320.)

1. Write proper Market Setting to the EEPROM

using the Adjustment Program.

At power-on

Anywhere

The printer does not perform the Ink
Replacement Cleaning and the error is
displayed on LED and STM3.

Ink Cartridge

1. Check if the Ink Cartridge is normal by installing it in

another printer.

1. Replace the Ink Cartridge with a new one.

The printer does not perform any print
operation and the error is displayed on
LED and STM3.

Ink Cartridge

1. Check if ink still remains in the Ink Cartridge.

2. Check if the Ink Cartridge is normal by installing it in

another printer.

1. Replace the Ink Cartridge with a new one.

2. Replace the Ink Cartridge with a new one.

Table 1-6. Check Points for Paper Out Error to Each Phenomenon

Occurrence Timing

Position of CR

Phenomenon Detail

Faulty Part/

Part Name

Check Point

Remedy

At operation

"Holder, Shaft, LD Roller" rotates to
feed paper, but "Hopper" does not
operate.

ASF Assy.

1. Check if "Hopper" works properly while feeding paper.

1. Reassemble "ASF Frame" and "Compression

Spring, 2.51" correctly.

Compression Spring, 2.51

Содержание R320 - Stylus Photo Color Inkjet Printer



















































































































Результаты поиска

Содержание R320 - Stylus Photo Color Inkjet Printer

Отзывы:

Похожие инструкции для R320 - Stylus Photo Color Inkjet Printer

Бренды по названию

Популярные бренды

Epson R320 - Stylus Photo Color Inkjet Printer, Руководство по обслуживанию

Результаты поиска

Содержание R320 - Stylus Photo Color Inkjet Printer

Отзывы:

Похожие инструкции для R320 - Stylus Photo Color Inkjet Printer

Бренды по названию

Популярные бренды