EPS PSB 10000 4U Скачать руководство пользователя

Страница: 62 / 110

30000800_manual_psb_10000_4u_30kw_en_04

3.6

Remote control

3.6.1

General

Remote control is possible via one of the built-in interfaces (analog, USB, Ethernet) or via one of the optional interface mod-

ules. One of the digital interface is the master-slave bus. It means that a Slave model is supposed to be controlled from a

master unit via the master-slave bus. Controlling a Slave device via its rear USB port is considered an exception.
Important here is that only the analog or any digital interface can be in control. It means that if an attempt was made to

switch to remote control via the digital interface whilst analog remote control is active (pin REMOTE = LOW) the device would

report an error via the digital interface. In the opposite direction, a switch-over via pin REMOTE would be ignored. However,

status monitoring and reading of values are always possible.

3.6.2

Control locations

Control locations are those locations from where the device can be controlled. Essentially there are two: at the device

(manual operation) and external (remote control). The following locations are defined:

Displayed location

Description

Remote: None

If neither of the other locations is displayed then manual control is active and access

from the analog and digital interfaces is allowed.

Remote: <interface_name>

Remote control via any interface is active

Local

Remote control is locked, only manual operation is allowed.

Remote control may be allowed or inhibited using the setting

Allow remote control

(see

“3.5.3.1. Sub menu “Settings””). In

inhibited condition the status “Local” will be displayed top right. Activating the inhibit can be useful if the device is remotely

controlled by software or some electronic device, but it’s required to make adjustments at the device or deal with emergency.
Activating condition

Local

causes the following:

•

If remote control via the digital interface is active (e. g.

Remote: USB

), then it’s immediately terminated and in order to con-

tinue remote control once

Local

is no longer active, it has to be reactivated at the PC

•

If remote control via the analog interface is active (

Remote: Analog

), then it’s temporarily interrupted until remote control is

allowed again by deactivating

Local

, because pin REMOTE continues to signal “remote control = on”, unless this has been

changed during the

Local

period.

3.6.3

Remote control via a digital interface

3.6.3.1

Selecting an interface

In addition to the built-in USB and Ethernet ports, all models of this series support the following optionally available interface

modules:

Short ID

Type

Ports Description*

IF-AB-CANO

CANopen

CANopen slave with generic EDS

IF-AB-RS232

RS232

Standard RS232, serial

IF-AB-PBUS

Profibus

Profibus DP-V1 slave

IF-AB-PNET1P

ProfiNet

Profinet DP-V1 slave

IF-AB-PNET2P

ProfiNet

Profinet DP-V1 slave, with switch

IF-AB-CAN

CAN

CAN 2.0 A / 2.0 B

IF-AB-ECT

EtherCAT

Standard EtherCAT slave with CoE

IF-AB-MBUS1P

ModBus TCP 1

ModBus TCP protocol via Ethernet

IF-AB-MBUS2P

ModBus TCP 2

ModBus TCP protocol via Ethernet

* For technical details of the various modules see the extra documentation “Programming Guide Modbus & SCPI”

3.6.3.2

Programming

Programming details for the rear interfaces, the communication protocols etc. are to be found in the documentation “Pro-

gramming Guide ModBus & SCPI“ which is supplied on the included USB stick or which is available as download from the

manufacturer’s website.

Содержание PSB 10000 4U















































































































Результаты поиска

Содержание PSB 10000 4U

Отзывы:

Похожие инструкции для PSB 10000 4U

Бренды по названию

Популярные бренды

EPS PSB 10000 4U, Руководство по эксплуатации

Результаты поиска

Содержание PSB 10000 4U

Отзывы:

Похожие инструкции для PSB 10000 4U

Бренды по названию

Популярные бренды