EPS PSB 10000 4U Скачать руководство пользователя

Страница: 49 / 110

30000800_manual_psb_10000_4u_30kw_en_04

3.5.3.1

Sub menu “Settings”

This sub menu can be accessed directly from the main screen by tapping the Settings button.

Group

Parameters & description

Presets

U, I, P, R

Presetting of all set values via on-screen numeric pad.

Protection

OVP, OCP, OPP

Adjust the thresholds of the protections

Limits

U-max, U-min etc.

Define the adjustment limits (find more information in

“3.5.4. Adjustment limits”)

User events

UVD, OVD etc.

Define supervision thresholds which can trigger user defined events (find more information in

“3.7.2.1.

User defined events”

)

General

Allow remote control

If remote control is allowed, the device can’t be controlled remotely over either the digital or analog

interfaces. This situation will be shown as “Local” in the status area on the main display. Also see sec-

tion

1.9.6.1.

R mode

Activates or deactivates the internal resistance control. If activated, the resistance set value and actual

will be shown the main screen. For details refer to

“3.3.4. Internal resistance regulation (source mode)”

and

“3.5.6. Manual adjustment of set values”.

Voltage controller speed

(Switching the speed only works if the device has already been delivered with firmware KE 3.02 or

higher)
This switch can be used to select the internal voltage controller speed which, as a result, impacts

possible system oscillation. For more information refer to

“3.3.7. Dynamic characteristics and stability

criteria”.

•

Slow

= the voltage controller will be a little slower, the oscillation tendency will decrease

•

Normal

= the voltage controller is on standard speed (Default)

•

Fast

= the voltage controller will be a little faster, the oscillation tendency will increase

SEMI F47

(Only displayed if the device has already been delivered with firmware KE 3.02 or higher)

Activates or deactivates a feature called SEMI F47 which is related to the equally named standard. See

“3.12.3. SEMI F47” for more information.

Analog interface Range

Selects the voltage range for the analog set values, actual values and reference voltage output.

•

0...5 V

= Range is 0...100% for set /actual values, reference voltage will be 5 V

•

0...10 V

= Range is 0...100% for set /actual values, reference voltage will be 10 V

Also see

“3.6.4. Remote control via the analog interface”

REM-SB Level

Selects how the input pin REM-SB of the analog interface shall be working regarding levels (see

“3.6.4.3. Analog interface specification”

) and logic:

•

Normal

= Levels and function as described in the table in

3.6.4.3

•

Inverted

= Levels and function will be inverted

Also see

“3.6.4.7. Application examples”

Содержание PSB 10000 4U















































































































Результаты поиска

Содержание PSB 10000 4U

Отзывы:

Похожие инструкции для PSB 10000 4U

Бренды по названию

Популярные бренды

EPS PSB 10000 4U, Руководство по эксплуатации

Результаты поиска

Содержание PSB 10000 4U

Отзывы:

Похожие инструкции для PSB 10000 4U

Бренды по названию

Популярные бренды