EPS PSB 10000 4U Скачать руководство пользователя

Страница: 66 / 110

30000800_manual_psb_10000_4u_30kw_en_04

3.6.4.5

Overview of the D-sub socket

3.6.4.6

Simplified diagram of the pins

Digital Input (DI)

It requires to use a switch with low resis-

tance (relay, switch, circuit breaker etc.) in

order to send a clean signal to the DGND.

V~0.5

AGND

Analog Input (AI)

High resistance input (impedance >40

kΩ) for an operation amplifier circuit.

12V

+10V

Digital Output (DO)

A quasi open collector, realized as high re-

sistance pull-up against the internal supply.

In condition LOW it can’t drive any load, only

sink small current, as shown in the diagram

with a relay as example.

V~2

AGND

Analog Output (AO)

Output from an operation amplifier cir

cuit, low impedance. See specifications

table above.

3.6.4.7

Application examples

a) Switching the DC terminal with pin REM-SB

A digital output, e.g. from a PLC, may be unable to cleanly pull down the pin as it may not

be of sufficiently low resistance. Check the specification of the controlling application.

Also see pin diagrams above.

In analog remote control, pin REM-SB is be used to switch the DC terminal of the device on and off. This

function is also available without analog remote control being active and can on the one hand block the

DC terminal from being switched on in manual or digital remote control and on the other hand the pin can

switch the DC terminal on or off, but not standalone. See below at “Remote control has not been activated”.

REM-SB cannot serve as a safety stop switch to securely deactivate the DC output in

case of emergency! For that an external emergency stop system is required.

It’s recommended that a low resistance contact such as a switch, relay or transistor is used to switch the

pin to ground (DGND).
Following situations can occur:

• Remote control has been activated

During remote control via analog interface, only pin REM-SB determines the states of the DC terminal, according to the level

definitions in

3.6.4.3. The logical function and the default levels can be inverted by a parameter in the setup menu of the

device. See

3.5.3.1.

If the pin is unconnected or the connected contact is open, the pin will be HIGH. With setting “Analog inter-

face” -> “REM-SB level” being set to “Normal”, it requests to switch the DC terminal on. So when activating

remote control, the DC terminal will instantly switch on.

Содержание PSB 10000 4U















































































































Результаты поиска

Содержание PSB 10000 4U

Отзывы:

Похожие инструкции для PSB 10000 4U

Бренды по названию

Популярные бренды

EPS PSB 10000 4U, Руководство по эксплуатации

Результаты поиска

Содержание PSB 10000 4U

Отзывы:

Похожие инструкции для PSB 10000 4U

Бренды по названию

Популярные бренды