EPS PSB 10000 4U Скачать руководство пользователя страница 24

Страница: 24 / 110

30000800_manual_psb_10000_4u_30kw_en_04

The actual values of current and power can be negative (signed) or positive (unsigned). A negative value belongs to sink

mode and indicates that the device is working as electronic load.
When the DC terminal is switched on the actual regulation mode is displayed as

CV, CC, CP

next to the corresponding

actual value, as shown in the figure above.

The set values can be adjusted with the rotary knobs next to the display screen or can be entered directly via the touchscreen.

When adjusting with the knobs, pushing the knob will select the digit to be changed. Logically, the values are increased by

clockwise turning and decreased by anti-clockwise turning.
General display and setting ranges:

Display

Unit

Range

Description

Actual voltage

0.2-125% U

Nom

Actual value of the voltage on the DC terminal

Set value of voltage

0-102% U

Nom

Set value for limiting the DC voltage

Actual current

0.2-125% I

Nom

Actual value of the current on the DC terminal

Set values of current

0-102% I

Nom

Set value for limiting the DC current

Actual power

W, kW 0.2-125% P

Nom

Actual value of power according to P = U * I

Set values of power

W, kW 0-102% P

Nom

Set value for limiting DC power

Actual resistance

-99999 / ∞

Actual value of the internal resistance

Set value of resistance

-102% R

Max

Set value for the internal resistance

Adjustment limits

ditto

0-102% nom

U-max, I-min etc., related to the physical quantities

Protection settings

ditto

0-110% nom

OVP, OCP, OPP (related to U, I and P)

Lower limit for resistance set value varies. See tables in section

1.8.3

•

Status display (upper right)

This area displays various status texts and symbols:

Display

Description

The HMI is locked

The HMI is unlocked

Remote:

The device is under remote control from....

Analog

...the built-in analog interface

ETH

...the built-in Ethernet interface

USB

& others

...the built-in USB port or a plug in interface module

Local

The device has been locked by the user explicitly against remote control

Alarm:

Alarm condition which has not been acknowledged or still exists.

Event:

A user defined event has occurred which is not yet acknowledged.

MS mode: Master (n Sl)

Master-slave mode activated, device is master of n slaves

MS mode: Slave

Master-slave mode activated, device is slave

FG:

Function generator activated, function loaded (only in remote control)

Data logging to USB stick active or failed

•

Area for assigning the rotary knobs and DC terminal status

The two rotary knobs next to the display screen can be assigned to various functions. This area shows the actual assign-

ments. These can be changed by tapping this area, as long as the panel is not locked.

The physical quantities on the depiction of the knob show the current assignment. The

left knob is always assigned to the voltage (U), while the right knob can be switched

by tapping on the depiction. Furthermore, the DC terminal status is indicated by two

LEDs (green = on).

There are following possible rotary know assignments:

Содержание PSB 10000 4U















































































































Результаты поиска

Содержание PSB 10000 4U

Отзывы:

Похожие инструкции для PSB 10000 4U

Бренды по названию

Популярные бренды

EPS PSB 10000 4U, Руководство по эксплуатации

Результаты поиска

Содержание PSB 10000 4U

Отзывы:

Похожие инструкции для PSB 10000 4U

Бренды по названию

Популярные бренды