EPS PSB 10000 4U Скачать руководство пользователя страница 54

Страница: 54 / 110

30000800_manual_psb_10000_4u_30kw_en_04

IF Settings

Description

Baud rate

Setup of the CAN bus speed or baud rate in typical value between 10 kbps and

1Mbps. Default:

500 kbps

ID Format

Selection of the CAN ID format and range between

Standard

(11 Bit ID, 0h...7ffh)

and

Extended

(29 Bit, 0h...1fffffffh)

Termination

Activates or deactivates CAN bus termination with a built-in resistor. Default: off

Data length

Determines the DLC (data length) of all messages sent from the device.

Auto

= length can vary between 3 and 8 bytes

Always 8 Bytes

= length is always 8, filled up with zeros

Base ID

Setup of the CAN base ID (11 Bit or 29 Bit, hex format). Default:

Broadcast ID

Setup of the CAN broadcast ID (11 Bit or 29 Bit, hex format). Default:

7ffh

Base ID Cyclic Read

Setup of the CAN base ID (11 Bit or 29 Bit, hex format) for cyclic read of several

object groups. The device will automatically send object data to the IDs defined

with this setting. For more information refer to the programming guide. Default:

100h

Base ID Cyclic Send

Setup of the CAN base ID (11 Bit or 29 Bit, hex format) for cyclic send of set values

along with status. For more information refer to the programming guide. Default:

200h

Cyclic Read Time: Status

Activation/deactivation and time setting for the cyclic read of status from the

adjusted

Base ID Cyclic Read

Range: 20...5000 ms. Default:

0 ms

(deactivated)

Cyclic Read Time: Set values (PS)

Activation/deactivation and time setting for the cyclic read of set values of U & I

(source mode) from the adjusted

Base ID Cyclic Read + 2

. Range: 20...5000 ms.

Default:

0 ms

(deactivated)

Cyclic Read Time: Limits values 1 (PS)

Activation/deactivation and time setting for the cyclic read of adjustment limits of

U & I (source mode) from the adjusted

Base ID Cyclic Read + 3

Range: 20...5000 ms. Default:

0 ms

(deactivated)

Cyclic Read Time: Limits values 2 (PS)

Activation/deactivation and time setting for the cyclic read of adjustment limits

of P & R (source mode) to the adjusted

Base ID Cyclic Read + 4

. Range: 20...5000

ms. Default:

0 ms

(deactivated)

Cyclic Read Time: Actual

Activation/deactivation and time setting for the cyclic read of actual values from

the adjusted

Base ID Cyclic Read + 1

Range: 20...5000 ms. Default:

0 ms

(deactivated)

Cyclic Read Time: Set values (EL)

Activation/deactivation and time setting for the cyclic read of set values of I, P

and R (sink mode) from the adjusted

Base ID Cyclic Read + 5

. Range: 20...5000

ms. Default:

0 ms

(deactivated)

Cyclic Read Time: Limit values (EL)

Activation/deactivation and time setting for the cyclic read of adjustment limits

of I, P and R (sink mode) from the adjusted

Base ID Cyclic Read + 6

. Range:

20...5000 ms. Default:

0 ms

(deactivated)

Module firmware

CAN module firmware version

IF Settings

Description

2 Baud rate

The baud rate is selectable, other serial settings can’t be changed and are defined

like this: 8 data bits, 1 stop bit, parity = none
Baud rates:

2400Bd

4800Bd

9600Bd

19200Bd

38400Bd

57600Bd

115200Bd

Содержание PSB 10000 4U















































































































Результаты поиска

Содержание PSB 10000 4U

Отзывы:

Похожие инструкции для PSB 10000 4U

Бренды по названию

Популярные бренды

EPS PSB 10000 4U, Руководство по эксплуатации

Результаты поиска

Содержание PSB 10000 4U

Отзывы:

Похожие инструкции для PSB 10000 4U

Бренды по названию

Популярные бренды