Entrematic Ditec DAS200 Скачать руководство пользователя | Manualshive

Страница: 46 / 56

background image

46

IP2266EN

EN

i

Parameters from C0 to C9= FUTURE USE.

Operator mode selector service indication (00÷01)

Yellow flashing service LED.
Service indication on operation mode selector.
No service indication (00).
Indicate service (01).

00

= Off

01

= On

Choose priority of the operation mode selector (25÷99)

FUTURE USE

Choose group of the operation mode selector (00÷10)

FUTURE USE

Choose display mode of the operation mode selector (00÷01)

In Show local mode the OMS shows the last setting made
on the OMS.
In Show system mode the OMS shows the setting that the
operator is put to. It is shown with one flach every 5s.
When the OMS is flashing every 5s it is not possible to change
the mode on the OMS.

00

= Show system mode.

01

= Show local mode.

AUTOMATIC

Choose terminal mode of the operation mode selector (00÷02)
00

=The buttons on OMS are disabled.

01

= The OMS adapts to system mode.

02

= The OMS keeps its selected mode.

AUTOMATIC

Mode selector, self service indication 00÷01)
COM500ES/ER

. Orange flashing service LED.

COM501ES/ER

. Magenta flashing service LED.

Self service indication on operation mode selector.

00

= Off. No self service indication.

01

= On. Indicate self service. Indicating a status or condition

that can be cleared by the owner e.g. a break-out door
is standing open.

Mode selector, key impulse (00÷02)

Key impulse to the operator can be made in the following
ways by pushing the symbol below.

COM500ES/ER

,

COM501ES/ER

,

00

= Disabled. Disables the possibility to give key impulse.

01

= Login Required. Login required on the OMS to enable

the possibility to give key impulse.
The login is configured through parameter 99 and b1.

02

= Enabled. Enables the possibility to always give key

impulse.

Bluetooth Power Mode (00÷02)
00

= Always disabled. The Bluetooth Power Mode is fully

disabled until other mode is set.

01

= Disabled in OFF mode. The Bluetooth Power Mode is

disabled in OFF mode.

02

= Always enabled. The Bluetooth Power Mode is fully

enabled until other mode is set.

«
...
44
45
46
47
48
...
»

Содержание Ditec DAS200

























































Отзывы:

Нет отзывов

Похожие инструкции для Ditec DAS200

Air-Cooled Automatics ACAPTS-1.0

Бренд: Bernard Страницы: 4

Бренд: ORIGO Страницы: 30

Бренд: Chicago Electric Страницы: 32

Бренд: LOTOS Страницы: 14

Gama HILO MIG 280 DOUBLE PULSED

Бренд: stayer Страницы: 72

Бренд: Baxi Страницы: 36

Бренд: KROME Страницы: 2

Evolve Glass SIM Kit

Бренд: Henderson Страницы: 25

Бренд: ibidi Страницы: 28

Бренд: ESAB Страницы: 12

Бренд: SHARKS Страницы: 61

Бренд: Pitney Bowes Страницы: 81

Бренд: BossWeld Страницы: 20

Бренд: Hobart Страницы: 32

Бренд: ubbink Страницы: 93

Бренд: Rothenberger Страницы: 48

Бренд: Jasic Страницы: 18

Бренд: Roger Technology Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды