Entrematic Ditec DAS200 Скачать руководство пользователя

Страница: 29 / 56

IP2266EN

9.2 Status indication on the display

The display shows the different impulses that are active. The status viewing starts with showing
“

” as for Status, then one or many numbers representing the different active impulses in to

the operator.
The different impulses are:

= Key Impulse

= Inner impulse

= Outer impulse

= Synchronisation

= Presence impulse 1

=Presence impulse 2

= Side Presence impulse 1

= Side Presence impulse 2

= Stop impulse

= Emergency open impulse

= Close command

= Nurse impulse

= Push and Go impulse

= Open-Close impulse

= Fire impulse

= Interlock Disable

Display

Char

act er

Display

Char

act er

Display

Char

act er

Display

Char

act er

Display

Char

act er

9.1 Display

test

When the display shows "

", push the SELECT button and each of the two display win-

dows make a rotating test pattern.

Verify that all seven segments of the two display windows are lit during the test. If not there is
a risk of misjudgment of the digits shown in a defective display.

When the display test is ﬁnalized the display shows two steady digits indicating the ﬁrst parameter.

Содержание Ditec DAS200

























































Результаты поиска

Содержание Ditec DAS200

Отзывы:

Похожие инструкции для Ditec DAS200

Бренды по названию

Популярные бренды

Entrematic Ditec DAS200, Техническое руководство

Результаты поиска

Содержание Ditec DAS200

Отзывы:

Похожие инструкции для Ditec DAS200

Бренды по названию

Популярные бренды