Entrematic Ditec DAS200 Скачать руководство пользователя | Manualshive

Страница: 39 / 56

background image

39

IP2266EN

EN

Side Presence Activation Distance (00÷99dm)

This is an inhibit signal for side presence.
The door will act according to the value entered in para-
meter 2A.
The value has to be according to local legislation. In an esca-
pe route the door has to open to 80% of the certified distance
(see parameter 11) within 3 sec. after an inner impulse.

00

= If value 00 is selected side presence impulse is valid

from fully closed to fully open position.

01-99

= The distance is counted from open position.

During opening, the side presence impulse is inhibited
until the door reaches the entered value in the parameter.

Sensor Type (00÷01)

Select type of monitoring for the combined sensors. Choose
between 1-wire (00) or 2-wire (01) monitoring.

00

= 1-wire monitoring. 1-wire monitoring is used when

combined sensors have only one monitoring input for
both presence and impulse field.

01

= 2-wire monitoring. 2-wire monitoring is used when a

sensor has separate monitoring inputs for both presence
and impulse field.

Active Brake on Stop (00÷01)
00

= Off. The door will freewheel until it stops.

01

= On. The operator will brake the doors actively during

1s on a Stop impulse.

Push & Go in EXIT and OFF Mode Selection (00÷01)
00

= Off.

01

= On.

Hold Force in EXIT and OFF Mode Selection (00÷01)
00

= Off.

01

= On.

With an electromechanical lock this hold force can be
unnecessary.

Toggle Operation Mode Seector after Stop (00÷01)

In operation mode selection OFF the mode must be changed
before normal operation after a Stop impulse.

00

= Off.

01

= On.

Emergency Action (00÷01)

Fire closing or Emergency opening.

00

= Closing (The door will close on fire impulse or power failure).

01

= Opening (The door will open on fire impulse or power failure).

NOTE

: on this DAS200RG this display is not visible and is set to 01.

Emergency Action in OFF Mode (00÷01)

Decides if “Emergency Action” shall be performed also in
modes election OFF (= opens also in the middle of the night).

00

= Off.

01

= On.

NOTE

: on this DAS200RG this display is not visible and is

set to 00.

«
...
37
38
39
40
41
...
»

Содержание Ditec DAS200

























































Отзывы:

Нет отзывов

Похожие инструкции для Ditec DAS200

Бренд: Bard Страницы: 54

Бренд: Lampert Страницы: 22

Бренд: HySecurity Страницы: 8

Бренд: HURNER Страницы: 69

Бренд: Allegion Страницы: 5

Demo Zone K1854-2

Бренд: Lincoln Electric Страницы: 22

Бренд: CAB Страницы: 40

Бренд: gala gar Страницы: 28

Бренд: Dometic Страницы: 24

Бренд: Hitbox Страницы: 18

WRD 0E4 K Series

Бренд: Salto Страницы: 10

Бренд: Parweld Страницы: 16

Бренд: F.F. Group Страницы: 82

Бренд: Viessmann Страницы: 44

Aristo YardFeed 2000

Бренд: ESAB Страницы: 32

Cigweld EasyWeld 160

Бренд: ESAB Страницы: 84

Бренд: Adtech Страницы: 134

DXR 230 REFERENCE

Бренд: Aereco Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды