Entrematic Ditec DAS200 страница 45 Скачать руководство пользователя

Страница: 45 / 56

IP2266EN

Choose group of the DAS902MP operation Mode selector,
terminals 9÷14 (00÷10)

FUTURE USE

ELECTRONIC OPERATION MODE SELECTOR PARAMETERS

Parameter

Description

Factory

setting

Installation

setting

Operation mode selector variant (01÷04)
01

= DO NOT USE.

= ELECTRONIC SELECTOR.

AUTOMATIC

Operation mode selector key lock (00÷03)
COM501ES/ER

There are four different levels of access code choices for
the operation mode selector.

COM500ES/ER

There are three different levels of access code choices for
the operation mode selector.

= No access code.

= Hold for two sec.

COM500ES/ER

, access is obtained by holding

for 2 seconds.

COM501ES/ER

, access is obtained by holding any mode

selection button for 2 seconds.

= Passcode.

COM500ES/ER

, passcode can be selected where the access

is obtained by briefly pushing in turn

The entire passcode must be entered within 3 seconds.

COM501ES/ER

, passcode can be selected where the access

is obtained by briefly pushing the buttons in correct order.
The entire passcode must be entered within 10 seconds.
The passcode can be changed through the DAS900CT.

Default passcode is

= Key

COM501ER

To enable the use of the selector, rotate the key clockwise
towards the symbol

COM500ER

mode selector is not affected by this parameter.
See parameter 99.

Содержание Ditec DAS200

























































Результаты поиска

Содержание Ditec DAS200

Отзывы:

Похожие инструкции для Ditec DAS200

Бренды по названию

Популярные бренды

Entrematic Ditec DAS200, Техническое руководство

Результаты поиска

Содержание Ditec DAS200

Отзывы:

Похожие инструкции для Ditec DAS200

Бренды по названию

Популярные бренды