Endress+Hauser Ceraphant PTP31B Скачать руководство пользователя страница 19

Страница: 19 / 92

Ceraphant PTC31B, PTP31B, PTP33B IO-Link

Installation

Hauser

A0025923

5.5

Mounting instructions for oxygen applications

Oxygen and other gases can react explosively to oils, grease and plastics, such that, among

other things, the following precautions must be taken:

• All components of the system, such as measuring devices, must be cleaned in accordance

with the BAM requirements.

• Dependent on the materials used, a certain maximum temperature and a maximum

pressure for oxygen applications must not be exceeded.

• The following table lists devices (devices only, not accessories or enclosed accessories),

which are suitable for gaseous oxygen applications.

Device

max

for oxygen applications

max

for oxygen applications

Option

PTC31B

40 bar (600 psi)

–10 to +60 °C (+14 to +140 °F)

Product Configurator, order code for "Service"

5.6

Post-installation check

 Is the device undamaged (visual inspection)?



Does the device comply with the measuring point specifications?
For example:
• Process temperature
• Process pressure
• Ambient temperature range
• Measuring range

 Are the measuring point identification and labeling correct (visual inspection)?

 Is the device adequately protected against precipitation and direct sunlight?

 Are the securing screws tightened securely?

 Is the pressure compensation element pointing downwards at an angle or to the side?

 To prevent moisture from penetrating, ensure that the connecting cables/plugs are pointing downwards.

Содержание Ceraphant PTP31B





























































































Результаты поиска

Содержание Ceraphant PTP31B

Отзывы:

Похожие инструкции для Ceraphant PTP31B

Бренды по названию

Популярные бренды

Endress+Hauser Ceraphant PTP31B, Руководство по эксплуатации

Результаты поиска

Содержание Ceraphant PTP31B

Отзывы:

Похожие инструкции для Ceraphant PTP31B

Бренды по названию

Популярные бренды