Empire DVCD32FP3-2 Скачать руководство пользователя страница 92

Страница: 92 / 96

36167-1-0316

Page 92

Maintenance precautions

Installation and repair should be done by a qualified service

person. The fireplace should be inspected before use and at least

annually by a qualified service person. more frequent cleaning

might be required due to excessive lint from carpeting, bedding

material, etc. It is imperative that control compartments, burners

and circulating air passageways of the fireplace be kept clean.

Keep burner and control compartment clean.

examine venting system periodically and replace damaged parts.

make a periodic visual check of pilot and burners. Clean and

replace damaged parts.

Damaged fireplace

Do not use this fireplace if any part has been under water.

Immediately call a qualified service technician to inspect the

fireplace and to replace any part of the control system and any

gas control which has been under water.

In the event of a natural disaster (tornado, earthquake, fire, etc.)

have a qualified technician inspect the fireplace for damage or

potential gas leaks. Repair or replace any damaged components

before operating this fireplace.

IMpORTANT SAfETY INfORMATION

for the Installer

•

Leave these instructions with the homeowner.

•

Replace any guard or protective device removed for

servicing prior to operating the fireplace.

•

During manufacture, this fireplace is treated with oils, films

and bonding agents. These are not harmful but may produce

smoke and odor as they burn off during initial operation. This

is normal.

•

Any modification to this fireplace or to controls can be

dangerous. Improper installation or use of the fireplace can

cause serious injury or death from fire, burns, explosion or

carbon monoxide poisoning.

•

Follow all local codes regarding installation, combustion and

ventilation air or in the absence of local codes follow the

National Fuel Gas Code ANSI Z223.1 (US installation), or

CAN/CGA-B149, Installation Code (Canada Installation)

•

Due to high temperatures, the fireplace should be located

out of traffic and away from furniture and draperies.

•

This fireplace must not share or be connected to a flue

serving a separate solid-fuel burning fireplace.

•

A barrier designed to reduce the risk of burns from the

hot viewing glass is provided with this fireplace and shall

be installed for the protection of children and other at-risk

individuals.

•

If the barrier becomes damaged, the barrier shall be

replaced with the manufacturer’s barrier for this fireplace.

•

Any safety screen, guard, or barrier removed to service a

fireplace must be replaced prior to operating the fireplace.

•

If this fireplace is installed directly on carpeting, tile or other

combustible material other than wood flooring the fireplace

must be installed on a metal or wood panel extending the full

width and depth of the fireplace.

The base referred to above does not mean the fireproof base

as used on wood stoves. The protection is for rugs that are

extremely thick and light colored tile.

•

Use Non-Combustible materials where indicated for the

fireplace installation. Non-combustible materials do not ignite

or burn as a result of using the fireplace. These include

metal, brick, ceramic, concrete, slate, glass, and plaster.

Adhesives must be rated for high temperatures (300°F +).

Any mechanical fasteners used to install material must also

be non-combustible, including wall anchors and tile spacers.

materials that pass the ASTm e 136 test (Standard Test

method for Behavior of materials in a Vertical Tube Furnace

at 750C) are considered non-combustible.

Содержание DVCD32FP3-2

































































































Результаты поиска

Содержание DVCD32FP3-2

Отзывы:

Бренды по названию

Популярные бренды

Empire DVCD32FP3-2, Инструкция по установке и руководство пользователя

Результаты поиска

Содержание DVCD32FP3-2

Отзывы:

Бренды по названию

Популярные бренды