Empire DVCD32FP3-2 Скачать руководство пользователя страница 3

Страница: 3 / 96

36167-1-0316

Page 3

Samples and Definitions:

DANgER

Indicates a hazardous situation which, if not avoided, will result

in death or serious injury.

WARNINg

Indicates a hazardous situation which, if not avoided, could

result in death or serious injury.

CAUTION

Indicates a hazardous situation which, if not avoided, could

result in minor or moderate injury.

NOTICE:

Addresses practices not related to personal injury.

Read all instructions before starting installation and follow them

carefully to insure safety. Failure to follow the instructions will

void the warranty and may cause a fire hazard.

The warranty will be voided by, and the warranter disclaims any

responsibility for the following actions:

•

Installation of any damaged fireplace or vent system

component.

•

modification for the fireplace or direct vent system.

•

Installation other than as instructed by empire Comfort

Systems.

•

Improper positioning of logs, glass door, or decorative

accessories.

•

Installation and/or use of any component part not

manufactured or approved by empire Comfort Systems.

All correspondence should refer to complete model Number,

Serial Number and type of gas. Fill out the Homeowner

Reference Section on page 5.

Television Considerations

Installing a television above a fireplace has become increasingly

popular; however, the area above any fireplace gets hot and most

TV manufacturers recommend against placing their products

near a heat source.

If you install a television above this fireplace, empire Comfort

Systems accepts no responsibility for damage or injuries. Follow

the television manufacturer’s installation instructions, including

any recommendations regarding proximity to heat sources.

If you have a TV above your fireplace, turn off the fireplace and

let it cool completely before servicing or touching any buttons on

the TV.

1. Determine where to install the fireplace. See page 11.

2. Frame the opening. See pages 14 - 15.

3. Install the fireplace. See page 15.

4. Install the venting. See pages 17 - 27.

5. Install and connect the gas lines. See pages 12 - 13.

6. Install the wiring. See pages 14, 70 and 74.

7. Light the fireplace. See pages 71 and 75.

8. Troubleshoot issues. See pages 72 and 76 - 78.

9. Place the serial number sticker located in the instruction

envelope onto the

“

Homeowner Reference Information

”

page.

bEfORE YOU START

10. Show the homeowner where the rating plate and lighting

instruction plate are located.

See figure 1.

11. Show the homeowner how to operate the fireplace.

12. Show the homeowner how to do the basic maintenance.

13. Read the safety information pages 92 - 94.

14. If located in the Commonwealth of massachusetts, note the

special requirements on page 95.

Unpacking the fireplace

1. Cut binding straps and shrink wrap.

2. Remove the top of the carton.

3. Carefully remove the carton contents.

4. Use the Carton Contents and Hardware Pack lists on page 4

to verify all components are present.

5. Verify that the fireplace and components have not been

damaged during shipping.

6. Set fireplace in a location near to its final installation location.

preparation

This fireplace and its components are safe when installed in

accordance with this Installation manual. Report any parts

damaged in shipment to your dealer. Do not install the fireplace

with damaged, incomplete or substitute parts.

Installation Considerations

•

Gas supply piping – right or left side entrance

•

electrical supply and connections – for optional fan kit

•

120V, 60Hz, 1 Amp

•

Right side entrance

•

Allowable fireplace mounting surfaces:

•

A flat, hard, combustible or non-combustible surface

•

A raised platform of combustible or non-combustible

material.

•

The four corners of the fireplace onto non-combustible

material so that contact is made on all four perimeter

edges on the bottom of the fireplace – such as on

cylinder blocks (where allowed by local codes).

•

If the fireplace is installed directly on carpeting, tile or other

combustible material other than wood flooring, it should be

installed on a metal or wood panel extending the full width

and depth of the fireplace.

•

This fireplace is designed to be installed in a zero-clearance

enclosure. Combustible material can come in contact with

the top and side standoff spacers, and the fireplace can be

secured to combustible framing with the framing brackets

provided with the fireplace.

VALVE

RATING

PLATE

LIGHTING

INSTRUCTION

PLATE

figure 1

Содержание DVCD32FP3-2

































































































Результаты поиска

Содержание DVCD32FP3-2

Отзывы:

Бренды по названию

Популярные бренды

Empire DVCD32FP3-2, Инструкция по установке и руководство пользователя

Результаты поиска

Содержание DVCD32FP3-2

Отзывы:

Бренды по названию

Популярные бренды