Empire DVCD32FP3-2 Скачать руководство пользователя страница 75

Страница: 75 / 96

36167-1-0316

Page 75

To TURN oFF GAS To FIRePLACe

1. SToP! Read the safety information above.

2. Turn oFF electric power to the fireplace.

3. Remove front surround panel assembly or bottom louver if

included.

4. Turn gas valve counterclockwise

“

”

position.

5. Wait ten minutes to clear out any gas. Then smell for gas,

including near the floor. If you smell gas, SToP! Follow

“

”

in the safety information above on this page. If you do not

smell gas, go to the next step.

6. Turn oN electric power to the fireplace.

7. Find pilot - Follow metal tube from gas control. The pilot is

behind the burner on the right side.

8. Turn main flame to on. If the pilot does not light within 60

seconds, stop and go to Step 5.

9. Refer to remote control instructions for detailed information,

control features, and operation.

NOTICE

: There is a CPI/IPI

switch that allows for a continuous standing pilot mode or

an intermittent pilot mode. See fireplace manual for location

of this switch. If the pilot or burner does not stay lit (in the

standing pilot mode), stop and immediately call a qualified

service technician or gas supplier.

10. If the burner or pilot does not operate properly after several

tries, turn the gas valve clockwise

“

oFF

”

and

call your service technician or gas supplier.

11. Replace the front surround assembly or close bottom louver

assembly.

12. operation of the gas valve is controlled by a manual on/

off switch or a hand held remote control. Refer to remote

instructions for detailed operation information.

LIGHTING INSTRUCTIoNS

FoR YoUR SAFeTY ReAD BeFoRe LIGHTING

WARNING: If you do not follow these instructions exactly, a fire or explosion may result

causing property damage, personal injury or loss of life.

INTERMITTENT pILOT LIghTINg INSTRUCTIONS

A. This fireplace has a pilot which can be lighted with the

manual on/off switch, a remote control, or by switching the

receiver switch to the

“

”

position. When lighting the pilot,

follow these instructions exactly.

B. BeFoRe LIGHTING smell all around the fireplace area for

gas. Be sure to smell next to the floor because some gas is

heavier than air and will settle on the floor.

WhAT TO DO If YOU SMELL gAS

Do not try to light any appliance. Do not touch any electrical

switch. Do not use any phone in your building. Immediately

call your gas supplier from a neighbor’s phone. Follow the

gas supplier’s instructions. If you can not reach your gas

supplier, call the fire department.

C. Use only the remote control or manual remote receiver

switch to operate the gas valve. Never use tools. If valve

does not operate, don’t try to repair it, call a qualified ser

vice technician. Force or attempted repair may result in a

fire or explosion.

D. Do not use this fireplace if any part has been under water.

Immediately call a qualified service technician to inspect the

fireplace and to replace any part of the control system and

any gas control which has been under water.

1. Turn off all electric power to the fireplace if service is to be

performed (if applicable).

2. Gain access to control compartment. Remove surround

panel assembly if necessary.

3. Locate on/off gas valve and turn clockwise to

“

oFF

”

. Do not force.

4. Close bottom louver assembly, if included.

Содержание DVCD32FP3-2

































































































Результаты поиска

Содержание DVCD32FP3-2

Отзывы:

Бренды по названию

Популярные бренды

Empire DVCD32FP3-2, Инструкция по установке и руководство пользователя

Результаты поиска

Содержание DVCD32FP3-2

Отзывы:

Бренды по названию

Популярные бренды