EMG ELDRO EdEx 125/160 Скачать руководство пользователя

Страница: 66 / 75

Maintenance

9.2

Maintenance tasks

/ 75

ELDRO-EdEx-Montageanleitung-607338-EN.docx

9.2.5

Changing the operating fluid

WARNING

Hot operating fluid

Risk of burns due to hot oil plumes upon opening the filling screw
when at operational temperature.

– The operating fluid may only be checked, topped up or

drained when switched off and cool.

– The EdEx thruster may only opened at a maximum

temperature of 40 °C.

NOTICE

If not filled sufficiently, the thruster does not develop the full lifting
force.

If overfilled, the thruster’s internal pressure is impermissibly high.



Position the EdEx thruster vertically above a suitable collecting

container



Remove filler and drain plug.



After the thruster has been completely emptied, close the drainage

opening firmly again



New operating fluid (

⇒

data on type plate)

The explosion-proof EdEx thruster is filled correctly if the fluid
level reaches the lower edge within the filling opening when the
thruster is upright and the lifting rod is retracted.



Perform several lifting movements to avoid possible air pockets



Then check the fill level again and top up operating fluid if

necessary



Tightly close the filler plug when the required fill level is reached



Dispose of used liquid (

⇒

Disposal chapter).

Содержание ELDRO EdEx 125/160












































































Результаты поиска

Содержание ELDRO EdEx 125/160

Отзывы:

Похожие инструкции для ELDRO EdEx 125/160

Бренды по названию

Популярные бренды

EMG ELDRO EdEx 125/160, Инструкция по сборке

Результаты поиска

Содержание ELDRO EdEx 125/160

Отзывы:

Похожие инструкции для ELDRO EdEx 125/160

Бренды по названию

Популярные бренды