EMG ELDRO EdEx 125/160 Скачать руководство пользователя | Manualshive

Страница: 48 / 75

background image

6

Assembly and installation

6.2

Electrical connection

48

/ 75

ELDRO-EdEx-Montageanleitung-607338-EN.docx



The cable gland and the screws of the housing cover must be
firmly tightened to ensure that the IP protection class is
maintained. Excessive tightening damages the seal and affects
the IP protection class.



If a pressure-proof cable entry with sealing ring is used, the
minimum length of the connection cable must not be less than 3
m.



The cables to be connected must be de-energised. Otherwise
there is a risk of damage to the EdEx thruster and ignition of an
explosive atmosphere.



All metallic housing parts of electrical equipment and other
conductive parts must be connected to the equipotential bonding
system.



The discharge from the housing of the EdEx thruster can be
designed as follows:
– external earth terminal (cross section: greater than 4 mm

2

)

– secured, metallic contact with construction points which are

connected to the equipotential bonding



The external ground terminal on the housing must be connected
with low resistance to the equipotential bonding of the potentially
explosive area.



No potential equalisation currents may flow between potentially
explosive areas and areas that are not potentially explosive.



The minimum cross section: 2 x 1.5 mm

2

or 1 x 4 mm

2



Discharging an electrostatic charge with a resistance between
0.2-1 mΩ is not considered grounding.



Any additional sensors that may be required must be suitable
and selected for the ambient conditions including the
corresponding zone, and installed according to the
manufacturer's specifications.

Further information is provided in the description of the power supply
connection (

⇒

Power supply connection section).

«
...
46
47
48
49
50
...
»

Содержание ELDRO EdEx 125/160












































































Отзывы:

Нет отзывов

Похожие инструкции для ELDRO EdEx 125/160

FreeStyle Comfort

Бренд: CAIRE Страницы: 33

Бренд: Hakko Electronics Страницы: 8

Professional HS 8

Бренд: Hailo Страницы: 5

Бренд: Hainbuch Страницы: 52

Бренд: Ransomes Страницы: 282

Ransomes HR 6010

Бренд: Jacobsen Страницы: 10

Бренд: Mangar International Страницы: 8

Бренд: Malvern Instruments Страницы: 30

Бренд: zarges Страницы: 36

ST60+ SPEED INSTRUMENT

Бренд: Raymarine Страницы: 60

Бренд: Raymarine Страницы: 15

Бренд: RaycoWylie Страницы: 9

Бренд: Raven Страницы: 58

Бренд: Raven Страницы: 26

Бренд: Ravo Страницы: 114

Бренд: Alcoscan Страницы: 6

Бренд: Gaspardo Страницы: 44

Бренд: Jackson Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды