EMG ELDRO EdEx 125/160 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 75

EMG ELDRO EdEx 125/160 Скачать руководство пользователя страница 10

1

General

1.8

Terms and abbreviations

10

/ 75

ELDRO-EdEx-Montageanleitung-607338-EN.docx

1.8

Terms and abbreviations

The following terms and abbreviations are used in the assembly
manual.

Table 2:

Terms and abbreviations

Term/abbreviation

Meaning

ATEX

ATmosphere EXplosible

Brake spring (C-spring)

Cylindrical pressure spring that counteracts the hydraulic force. As a
result, only the force difference on the lifting rod is effective as the
actuating force.

Damping spring (D-spring)

Spring for gentle braking. This reduces the braking force by applying the
brake shoes continuously until the stop value is reached. When bleeding
the brake, the braking force reduces continuously from the highest value
to zero (releasing the brake shoes). This function is only available in
combination with the C-spring.

ED

Duty cycle

EdEx thruster

Electro-hydraulic lifting thruster in explosion-proof design that converts
electrical energy into mechanical energy in a straight line movement by
hydraulic means

EN

European standard

EPL

Equipment Protection Level

Highest value for additional
load

Total of the forces that apply to the lifting rod head and that affect the
lifting movement and setting time, e.g. friction and mass of the connection
elements

Lifting valve H

Valve to reduce the lifting speed

Throttle valve D

Valves to reduce the lifting and lowering speeds

Lifting time

Time from switching the motor on until the top piston limit position is
reached

Nominal operating point

Operating point that is at 1/3 of the nominal lift

Nominal lift

Maximum path that the extending lifting rod can take

Nominal reset force

Minimum force at the nominal operating point for a machine with reset
spring C

Nominal actuating force

Usable hydraulic force on the lifting rod head for a machine without reset
spring c

Regulation braking

Braking to regulate three-phase motors to low speeds, virtually
independent of the load. A pump wheel with optimum adjustment
determines the hydraulic force with the nominal reset force. Thrusters for
regulation braking are equipped with reset spring C and damping spring
D.

Regulating spring (R-spring)

See damping spring

Reset spring

See brake spring

Lowering valve S

Valve to reduce the lowering speed

«
...
8
9
10
11
12
...
»

Содержание ELDRO EdEx 125/160












































































Отзывы:

Нет отзывов