PG4UW software
81
Even
Device [ADDR]
Buffer [2*ADDR]
Odd
Device [ADDR]
Buffer [1+ (2*ADDR)]
1./4
Device [ADDR]
Buffer [4*ADDR]
2./4
Device [ADDR]
Buffer [1+(4*ADDR)]
3./4
Device [ADDR]
Buffer [2+(4*ADDR)]
4./4
Device [ADDR]
Buffer [3+(4*ADDR)]
Real addressing will be following: (all addresses are hexadecimal)
Split
type
Device
addresses
Buffer addresses
None
00 01 02 03 04 05
00 01 02 03 04 05
Even
00 01 02 03 04 05
00 02 04 06 08 0A
Odd
00 01 02 03 04 05
01 03 05 07 09 0B
1./4
00 01 02 03 04 05
00 04 08 0C 10 14
2./4
00 01 02 03 04 05
01 05 09 0D 11 15
3./4
00 01 02 03 04 05
02 06 0A 0E 12 16
4./4
00 01 02 03 04 05
03 07 0B 0F 13 17
Terms explanation:
Access to device address ADDR is written as Device[ADDR].
Access to buffer address ADDR is written as Buffer[ADDR].
ADDR value can be from zero to device size (in bytes).
All addresses are byte oriented addresses.
group
Insertion test:
insertion test
(default ENABLE)
If enabled, the programmer checks all pins of the programmed chip, if it has proper
connection to the ZIF socket (continuity test). The programmer is able to identify the wrong
contact, bad inserted chip and also (partially) back inserted chip.
Device ID check error terminates the operation
(default
ENABLE)
Programmer provides ID check before each selected action. It compares read ID codes from
device with ID codes defined by device manufacturer. In case of ID error, control program
behaves as follows:
- if item is set to ENABLE, selected action is finished
- if item is set to DISABLE, selected action continues. Control program just writes warning
message about ID error to LOG window.
If enabled, the programmer checks the electronic ID of the programmed chip.
Note 1
:
Some old chips don't carry electronic ID.
Note 2: In some special cases, several microcontrollers don't provide ID, if copy protection
feature in the chip is set, even if device ID check setting in control program is set to "Enable".
group
Command execution:
blank check before programming
(default DISABLE)
erase before programming
(default DISABLE)
verify after reading
(default ENABLE)
verify
(ONCE, TWICE)
verify options
(nominal VCC +/-5%
nominal VCC +/-10%
VCCmin - VCCmax)
Содержание BeeHive304
