ELNA eXpressive 970 Скачать руководство пользователя

Страница: 3 / 65

Replacing the Jump Solenoid .....................................................................................

Adjusting a Play in the Moving Head ..........................................................................

Replacing the Moving Head (1) ..................................................................................

Replacing the Moving Head (2) ..................................................................................

Adjusting the Needle Drop Position (Back or Forth) ..................................................

Adjusting the Needle Height .......................................................................................

Replacing the Needle Bar, Needle Spring and Cushion .............................................

Replacing the Rotation Stopper Plate ........................................................................

Replacing the Thread Take-up Lever ..........................................................................

Adjusting the Check Spring Tension ...........................................................................

Adjusting the Check Spring Stroke ............................................................................

Adjusting the Thread Catcher Holder .........................................................................

Replacing the Thread Catcher Loop Tape ..................................................................

Replacing the Lateral Moving Unit ..............................................................................

Adjust the Hook Timing...............................................................................................

Adjusting the Position of the Hook Stopper ................................................................

Replacing the Thread Cutter Driving Roller ................................................................

Replacing the Dynamic Cutter Blade ..........................................................................

Replacing the Static Cutter Blade ...............................................................................

Adjusting the Static Cutter Blade ................................................................................

CONTENTS

Содержание eXpressive 970


































































Результаты поиска

Содержание eXpressive 970

Отзывы:

Похожие инструкции для eXpressive 970

Бренды по названию

Популярные бренды

ELNA eXpressive 970, Руководство по обслуживанию

Результаты поиска

Содержание eXpressive 970

Отзывы:

Похожие инструкции для eXpressive 970

Бренды по названию

Популярные бренды