manualshive.com logo in svg

ELNA eXpressive 970, Руководство по обслуживанию

Поделиться
Скачать
ELNA eXpressive 970 Скачать руководство пользователя страница 25

24

Needle bar height
gauge

Step 3: Adjusting the Height of the Needle Bar

    and Presser Foot

12 Remove the bobbin case.
13 Hold the needle bar holder and push the needle bar

down until it clicks.

14 Lower the needle bar to the lowest position by turning

the hand wheel.

15 Insert the needle bar height gauge into the hook.

16 Knock on the top of the needle bar gently until the tip

of the needle contact the gauge.
Turn the gauge to find if the needle reaches the gauge.
Set the direction of the needle bar so the hole in the
needle bar faces directly the front.

17 Tighten the needle bar holder screw securely.

Note: Check if the needle bar is securely fixed by

      turning the cap screw clockwise.

18 Loosen the setscrew (B).
19 Insert the 1.2 mm thickness gauge between the

presser foot and needle plate. Press the presser foot
down against the gauge.

20 Tighten the setscrew (B) securely.
21 Remove the needle bar height gauge.
22 Turn the hand wheel to match the alignment line on it

with the joint of the right and left covers (the upper
shaft will be set at 270 degrees).

* To replace the spring and washer on other needle

bars, follow the above steps (select the relevant needle
bar in the Needle Change adjusting window).

23 Attach the tension control unit and thread catcher panel

(head cover). Lower thread guide plate and tension
unit cover.
Note: Be sure not to get wires caught between covers.

Adjust the position of the tension unit cover so
the arch of the cover aligns with the tension
dials.

Step 4: Test Sewing

Insert the test pattern card into the RCS unit and sew the
test pattern.
Use a 120 deniers rayon thread or equivalent for needle
and a #120 cotton or polyester thread for bobbin.

Needle rest (view from the side
of the moving head)

Needle bar
holder screw

Hole in the
needle bar

Presser foot

Thickness gauge
 (1.2 mm)

Alignment line

Tension dial

Tension unit cover

Arch

Setscrew

(B)

Joint of the right and left
covers

Cap
screw

Arch

Tension dial

Tension unit cover

Содержание eXpressive 970


































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды