manualshive.com logo in svg

ELNA eXpressive 970, Руководство по обслуживанию

Поделиться
Скачать
ELNA eXpressive 970 Скачать руководство пользователя страница 41

40

Replacing the Lateral Moving Unit

To remove:
1.  Remove the spool stand, right cover and left cover 
  (see pages 4 and 5).

2.  Remove the tension unit cover (see page 4).

3.  Remove the three setscrews (A) and remove the 
  driver cover.

4.  Disconnect the connectors.

5.  Remove the two setscrews (B) and remove the lateral  
  moving unit.

To attach:
6.  Attach the lateral moving unit and loosely fix it with the  
  two setscrews (B).

7.  Push the needle bar down and rotate the handwheel 
  to set the index disk at “L”.

8.  Adjust the position of the lateral moving unit so the 
  needle enters into the center of the hole in the needle  
  plate. Tighten the two set screws (B) securely.

9.  Connect the connectors and attach the parts removed  
  in steps 1 to 3.

Setscrews (A)

Setscrews (B)

Connector

Hole in the needle plate

Needle

Drive cover

Connector

Содержание eXpressive 970


































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды