ELNA eXpressive 970 Скачать руководство пользователя | Manualshive

Страница: 45 / 65

background image

44

Replacing the Dynamic Cutter Blade

Setscrews

Setscrew

Drive shaft ring

Setscrews

Drive shaft unit

Lever unit

Link shaft

1. Remove the setscrews and needle plate.

2.  Turn the power switch on while pressing the Start/
  Stop button and Thread cutter button at the same time
  to open the

Factory Adjusting window.

Press the

Phase key to open the Phase Sensor

adjusting window and press the

All Int key.

Press the

Cancel key to return to the previous

window.
Press the

Cut Adjust key to open the Cut Motor

adjusting window. Press

Divide key to move the

dynamic cutter blade forward.

3. Loosen the setscrew and remove the drive shaft ring.

4.  Remove the cutter drive shaft unit from the frame.
  Remove the two setscrews and replace the dynamic
  cutter blade.

5. Insert the drive shaft into the frame and link pin of the
cutter drive shaft unit into the hole in the lever unit.

6.  Attach the drive shaft ring and tighten the setscrew
  while pressing the ring and shaft unit each other with
  your fingers.

NOTE:
Be sure that there is no thrust play in the shaft unit.

7. Adjust the cutter blades position (see following pages)
and test auto thread cutting.

8. Attach the needle plate.

«
...
43
44
45
46
47
...
»

Содержание eXpressive 970


































































Отзывы:

Нет отзывов

Похожие инструкции для eXpressive 970

Бренд: Singer Страницы: 34

Бренд: Kärcher Страницы: 55

Бренд: U.S. Products Страницы: 10

CONTOUR 350 DELUXE

Бренд: H. Winter Страницы: 23

1500 Contractors

Бренд: MasterCraft Страницы: 8

Бренд: Kärcher Страницы: 5

Бренд: Mitsubishi Страницы: 32

Бренд: Kettler Страницы: 36

Бренд: JUKI Страницы: 8

Бренд: Panasonic Страницы: 74

Бренд: Panasonic Страницы: 84

Бренд: Panasonic Страницы: 88

Бренд: Panasonic Страницы: 86

Бренд: Panasonic Страницы: 90

Бренд: Panasonic Страницы: 54

Бренд: Tunstall Страницы: 20

Бренд: Antari Страницы: 28

Бренд: Antari Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды