ELNA eXpressive 970 Скачать руководство пользователя страница 62

Страница: 62 / 65

Setscrew

1. Remove the spool stand, right cover, left cover and
tension control panel (see pages 4 – 6).

2. Open the factory adjusting menu window and press
the

Needle key to open the Needle Change adjusting

window.

3.  Turn the lateral movement idler gear to set the lateral
  movement cam at the middle of the flat portion.
  The indication next to

NCHM Init Sen should be “H”.

  To adjust the stop position, loosen the setscrew and
  turn the stop positioning shield plate.
  Tighten the setscrew.

NOTE:
The shield plate should not interfere with the sensor.

4. Press Init key to move the head to the stop position
and check if “

L” is indicated.

5. Attach the parts removed in step 1.

Lateral
movement
idler gear

Stop position
shield plate

Phase reference of the
lateral movement cam and
stop position shield plate

Adjusting the Moving Head Stop Position

Содержание eXpressive 970


































































Результаты поиска

Содержание eXpressive 970

Отзывы:

Бренды по названию

Популярные бренды

ELNA eXpressive 970, Руководство по обслуживанию

Результаты поиска

Содержание eXpressive 970

Отзывы:

Бренды по названию

Популярные бренды