manualshive.com logo in svg

ELNA eXpressive 970, Руководство по обслуживанию

Поделиться
Скачать
ELNA eXpressive 970 Скачать руководство пользователя страница 65

64

Securing the Cables in the Moving Head (Upper Part)

Secure the cables with the Nylon clip and cable 
guides to prevent the cables from interfering with 
parts in the moving head.

Left LED cables

Nylon clip

Right LED cables 
and other cables

Cable guides

Attaching the cable guide (black)

Bundle the cables with the Nylon clip and attach the 
cable guide (black) to the Nylon clip with the setscrew.

* Attach the cable guides (white) under the cord guide   
  plate.

Nylon clip

Cable guide (black)

Setscrew

Bending the cable guide (black)

Bend the cable guide (black) in line with the left edge 
of the cord guide plate (upper part) and level with the 
cables A, as illustrated.
* The cables should be under the cable guide (black) 
when the moving head moves.

Bending the cable guides (white)

Bend the 3 cable guides (white) upright on the edge 
of the cord guide plate (lower part).
* The cables should be inside the cable guides (white) 
when the moving head moves.

Cables A

Cable guide (black)

Cord guide plate

Cable guides (white)

Cable guide (black)

Cable guides (white)

Содержание eXpressive 970


































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды