manualshive.com logo in svg

ELNA eXpressive 970, Руководство по обслуживанию

Поделиться
Скачать
ELNA eXpressive 970 Скачать руководство пользователя страница 39

38

1.  Remove the right cover of the stationary head (see 
  page 5).

2.  Remove the thread catcher panel and lower thread 
  guide plate (see pages 25 and 26).

3.  Loosen the four setscrews (A).

4.  Pull the thread catcher out to set the tip of the thread 
  catcher on the lower thread catcher holder.
  Move the thread catcher holder up or down so the 
  lower surface of the thread catcher touches the upper  
  surface of the lower thread catcher holder.

NOTE:
If an adjustment allowance of the thread catcher holder is 
not enough, loosen the three setscrews (B) and move the 
thread catcher unit.

5.  Check if the thread catcher moves smoothly by  

 

  moving the rod shaft with your hand.
  Tighten the four setscrews (A).

6.  Press the thread cutter button to test thread cutting 
  and catching.

7.  Attach the parts removed in steps 1 and 2.

Adjusting the Thread Catcher Holder

Setscrews (A)

Rod shaft

Lower thread 
catcher holder

Thread catcher

Setscrews (B)

Содержание eXpressive 970


































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды