ELNA eXpressive 970 Скачать руководство пользователя страница 9

Страница: 9 / 65

Detecting roller

To avoid seam puckering, skipped stitches or thread
breaking, keep the thread paths in the best condition.

1.  Tension control, detecting roller
  a)  Detecting rollers should spin smoothly.
  b)  Tension controls and detecting rollers

should be free of lint or dust.

2. Thread guide hole
a) There should be no burrs or scratches.

3. Thread take-up lever
a) There should be no burrs or scratches.

4. Lower guide plate
a) There should be no burrs or scratches.

5. Needle
a) The needle should not be bent or blunt.

To check the needle:

Touch the tip of the needle and slide it over on your nail

and slid it lightly.

The needle must be blunt if there is any scratch on your

nail after sliding the needle on your nail.

In that case, replace the needle.

Place the flat side of the needle onto something flat

(needle plate, glass, etc.). The gap (A) between the
needle and the flat surface should be consistent.

Replace the needle if the gap is not consistent.

Checking the Thread Paths (1)

Содержание eXpressive 970


































































Результаты поиска

Содержание eXpressive 970

Отзывы:

Бренды по названию

Популярные бренды

ELNA eXpressive 970, Руководство по обслуживанию

Результаты поиска

Содержание eXpressive 970

Отзывы:

Бренды по названию

Популярные бренды